Series 10-MGF Guide table ø40, ø63, ø100 Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
S1 S2 Preset pressure OFF OFF P1 ON OFF P2 OFF ON P3 ON ON P4 For safety reasons, it is recommended that one of the preset pressures be set to 0MPa. 1.12-16
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 3-12-6
There may be large variations depending on the surrounding environment (variations as much as 30%). 12 Compact Cylinder Series CQ2 Auto Switch Mounting Contact Protection Boxes/CD-P11, CD-P12 Auto Switches/Proper Mounting Position for Stroke End Detection D-Z7 and D-Z8 type switches do not have internal contact protection circuits.
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Installation location Do not install this product in an area that is exposed to rainwater or direct sunlight. Do not install in locations influenced by vibrations. If it must be used in such an area due to unavoidable circumstances, please contact SMC beforehand. 1016 Booster Regulator VBA Series Handling Caution 3.
O F S TAT I O N S Correct 1 1 station to 6 6 stations W I R I N G DO NOT chamfer the nozzle No terminal box L Terminal Box wiring on Left Hand Side R Terminal Box wiring on Right Hand Side O P T I O N B Bracket G Gauge Incorrect D I M E N S I O N S S E E P A G E 7.16 Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 !
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Do not disassemble, except for when replacing any of the replaceable parts, as this may cause the performance to deteriorate. In the case of a rubber cover, the lock can be released easily by hitting the round tab on the cover with a plastic hammer. 3.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only. They can cause the coil to burn out. 3.
Caution D: With connector DO: Without connector Y: With connector YO: Without connector When using the surge voltage suppressor type, residual voltage will remain. For details, refer to the Web Catalog (VP300/500 Low wattage specification). * Refer to the Web Catalog (VP300/500 Low wattage specification) for details of the DIN terminal. Assembly Example Products do not come assembled.
Contact Protection Box/CD-P11, CD-P12 The D-Z7, D-Z8 and D-A9 type switches do not have built-in contact protection circuits. Use a contact protection box in cases such as with an induction load, when the lead wire is longer than 5m or with 100VAC. 1 Operating load is an induction load. 2 Wiring to the load is 5m or longer.
Do not dispose this fluid in the environment.
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display. Note 3) Window comparator mode Since hysteresis is 3 digits, separate P1 and P2 by 7 digits or more. 1 digit is the minimum setting unit (refer to the table above).
D -DIN connector DL -DIN connector with light DO-For DIN connector (without connector) Orifice and port size combinations T -With conduit terminal TL-With conduit terminal/light Class Orifice diameter Port size 2 3 4 5 7 10 1/8 (6A) 2 1/4 (8A) 1/4 (8A) 3 3/8 (10A) 1/2 (15A) Connector 1/4 (8A) 3/8 (10A) 4 All class B coils are equipped with surge voltage suppressor.
Mechanical Valve Series VM Model VM1000 VM100 VM200 Side piping Bottom piping Side piping Bottom piping Dimensions (mm) 11 X 36 X 16 11 X 28 X 25 17 X 44 X 25 17 X 44 X 30 25 X 40 X 52 Basic Roller Lever One Way Roller Lever Straight Plunger Roller Plunger Cross Roller Plunger Toggle Lever Push Button (Mushroom) Push Button (Extended) Push Button (Flush) Twist Selector (2 position) Key Selector
The VQ20/30 series is a pilot operated, two port multi-media valve. The series is compact and lightweight with a large flow capacity. The VQ20/30's long life, high speed coil (up to 20 million cycles at 100cps for pneumatic use) along with its all plastic construction, make it an excellent choice for those who want high performance at a lower cost.Manifold for VQ20/30 pilot operated valve
Do nol apply voltage potential In excess of 250V. (Note) Indicator oanel Denatured PPO Swagelok* IS a registered trademark 0 1 Crawford Fitting Co. VCRlI lS a registered trademark. of Cajon Co.
Note 5) Do not use the V-band type for gases. FGES/FGEL type (V-band type) FGET type (Bolt tightening type) Suitable for medium flow rate, low pressure filtration. Element replacement is easy with the V-band type.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4