SMC Corporation of America
Elite Part Number Search
Search Results "HRL100-AN-40"

Can hold an intermediate cylinder position for an extended time. When combined with a double check spacer with built-in double check valve, it is unaffected by air leakage between the spool valves, making it possible to hold a cylinder at an intermediate stopping position for an extended time.

Dealing with the stroke by making an exclusive body. Description 12 to 32: Available by the 1 mm stroke interval. All bore sizes are available by the 1 mm interval. 40 to 100: Available by the 5 mm stroke interval. Add -XB10 to the end of standard model number. Model no.

An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.

The spacers specification can be changed (from an individual SUP spacer to an individual EXH spacer) by changing the coupling of the fittings and bushing.

40 40 40 40 40 Suction flow rate Suction flow rate 20 20 20 20 20 20 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0 0 0 0 0 10 20 30 40 50 5 10 15 20 25 Supply pressure (MPa) Suction flow rate (l/min(ANR)) Supply pressure (MPa) Suction flow rate (l/min(ANR)) How to Read Flow Characteristics Graph The flow rate characteristics indicate the relationship between the vacuum pressure

When you begin to feel that the screw is being tightened, turn it an additional 90.

The valve coil is kept in a deenergized state even when there is an electric signal from the connector. Normal operating condition. Switching of valve is based on an electric signal from the connector.

The valve coil is kept in a deenergized state even when there is an electric signal from the connector. Normal operating condition. Switching of valve is based on an electric signal from the connector.

Endurance Test An ozonizer was used in a pneumatic circuit to prepare air to an ozone concentration of 1ppm. The test specimens (system components made from HNBR and NBR) were operated using this ozoneladen compressed air, and the endurance of each type of component/material was measured and compared.

) tGauge port (Outlet) 2P 3P 4PL 5PC MPA MPA MPA 1 1 1 0 0 40 2) Other range available.

for 20, 50% for 32, 55% for 40 and 60% or less for 50, respectively.)

55 75 F 17 26 41 52 G 40 39 63 68 H 87 91 129 142 J XLAQ-16 XLAQ-25 XLAQ-40 XLAQ-50 40 50 65 70 Note) The heater (Option) is not available with XLAQ-16. 471 Aluminum One-touch Connection and Release High Vacuum Angle Valve 2-step Control, Single Acting/Bellows Seal, O-ring Seal XLDQ Series How to Order XLDQ M9N A 40 q w e r t y w Actuator port direction q Flange size Rear flange surface

Note: Monosashi-kun with Brake (CE2)s bore size setting Blinking 63 80 100 25 32 40 50 DOWN UP range from 40 to 100. After setting of cylinder bore size, press WRITE to switch to the next input condition. The display will indicate PRG STEP P5 and the current load rate, which is blinking. Next, enter correct load rate.

& X160 options available on 25 40 boro 6rze9 omy, Proof pressure 06, 10 85psi {5.98k9f/cm'} o 15-40 101psi {7.1kgflcm'?}

& X160 options available on 25 40 boro 6rze9 omy, Proof pressure 06, 10 85psi {5.98k9f/cm'} o 15-40 101psi {7.1kgflcm'?}

& X160 options available on 25 40 boro 6rze9 omy, Proof pressure 06, 10 85psi {5.98k9f/cm'} o 15-40 101psi {7.1kgflcm'?}

ZSP ISA2 Fig. (2) Equivalent circuit of an NPN switch with the output off PLC Low level 12 to 24 [VDC] IS Main circuit of switch Max. 80 [mA] Max. 30 [V] ZSM Load PF2 Current flows. Load is powered. IF Fig. (3) Equivalent circuit of an NPN switch with the output on Data PNP 12 to 24 [VDC] Fig. (4) shows an example of a PNP switch.

This doubles as a screw hole for mounting. 8 Connector for an output device x 4 Connector for an output device. (PIN2, PIN4: output) 9 Connector for an input device x 4 Connector for an input device. (PIN2, PIN4: input) -23No.EX-OMZ0016-C LED EXW1-RD* The LED indicators at the top right corner of the compact wireless Remote indicate the power supply, communication and diagnostic status.