VM : One-touch fitting 1(P): Male thread 2(A): One-touch fitting 1(P): One-touch fitting 2(A): Male thread 1(P): Male thread 2(A): Male thread 2(A) 2(A) 2(A) 2(A) Applicable tubing O.D.
ARJ AR425 to 935 Air-operated type Pilot pressure VBA11A VBA10A, 20A, 40A, 43A ARX Drive chamber A Governor Drive chamber A Governor Drive chamber B Booster chamber A AMR IN (Inlet) IN (Inlet) Drive chamber B ARM VBA22A, 42A Piston rod Piston rod ARP Booster chamber A IR-A Piston Piston IR Check valve Booster chamber B Booster chamber B Check valve IRV Switching valve Switching valve E OUT
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
The Pressure switch is a UL approved product only if it has a mark on the body. A pressure sensor of stainless steel diaphragm is used for this product.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Normal output Reversed output P_1(P_2)=A-(A-B)/4 n_1(n_2)=B+(A-B)/4 A = Maximum pressure H_1(H_2)= (A-B)/2 H_1(H_2)= (A-B)/2 B = Minimum pressure If setting is not necessary press the UP and DOWN buttons simultaneously for 1 second or longer. -39No.PS-OMV0009-E [F 6] Fine adjustment of display value This function is to manually perform a fine adjustment of the displayed pressure value.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -14No.PS-OMV0004-H Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm. Piping specification: -F02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting.
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -13No.PS-OMW0002-C Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm. Piping specification: -F02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting.
No cracks, breaks or other damage occurred in a drop test from a 2-meter height or in a human stomp test.
When a system hazard can be expected due to a drop in vacuum pressure caused by power loss or vacuum pump trouble, install a safety circuit and configure the system so that it can avoid the danger. 2. When a system hazard can be expected with a malfunction of the vacuum regulator, install a safety circuit and configure the system so that it can avoid the danger. 1.
In the graph, find where the lines repres-enting a load weight of 10 kg and a stroke of 300 mm intersect. A 50 bore size is selected.
Due to the compressibility of air as a fluid, the actuator will continue to move until it reaches a position of pressure balance, even though the pilot check valve closes with an intermediate stop signal. 2. This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage.
DIN rail is not suitable for port size F02 (G1/4). No lead wire 1
Realizes momentary intermediate stoppage of a cylinder and able to adjust speed control of it. Tubing mount direction is 360 free. Electroless nickel plated is provided as standard. Applicable tubing O.D.
Nozzle Diameter: 13 (ø1.3mm), Vacuum Pressure: L (-48 kPa: ZH05 to 13D*A; -66 kPa: ZH15 to 20D*A), SUP: F01 (Screw-in G1/8), VAC: F02 (Screw-in G1/4), EXH: F02 (Screw-in G1/4)
Regulator Unit Combination: Others, Port Size: Rc1/8, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Standard Flow (Left to Right)] Left to right, Drain Cock: [Not Provided] No, Pressure Gauge: -, Residual Pressure Relief 3-Port Connection Valve: None, Set Pressure: -, Pressure Unit: Name plate and pressure gauge unit: MPa, T shape
Regulator Unit Combination: Others, Port Size: Rc1/8, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Standard Flow (Left to Right)] Left to right, Drain Cock: [Not Provided] No, Pressure Gauge: -, Residual Pressure Relief 3-Port Connection Valve: None, Set Pressure: -, Pressure Unit: Name plate and pressure gauge unit: MPa, T shape
Regulator Unit Combination: Others, Port Size: G1/8, Case Material: [Resin] Polycarbonate Case, Case Guard: No, Exhaust Structure: Relief type, Flow Direction: [Standard Flow (Left to Right)] Left to right, Drain Cock: [Not Provided] No, Pressure Gauge: No (No Pressure Port Plug), Residual Pressure Relief 3-Port Connection Valve: None, Set Pressure: 0.05 to 0.7 MPa, Pressure Unit: Name plate