Electric Actuator / Slider type 《 Battery-less absolute encoder type (Step motor 24VDC) 》 550 10 to 300 Parallel Stroke 701 to 800 20 to 550 12 to 330 6 to 180 24 to 750 16 to 500 8 to 250 30 to 750 20 to 550 10 to 300 range 801 to 900 24 to 610 16 to 410 8 to 200 30 to 750 20 to 550 10 to 300 901 to 1000 24 to 500 16 to 340 8 to 170 30 to 750 20 to 520 10 to 250 1001 to 1100 30 to 660 20 to 440 10 to 220 1101 to 1200 30 to 570 20 to 380 10 to 190 Max acceleration/deceleration
20 30 20 30 20 Min. speed [mm/s] (Speed tuning control) 38 25 38 25 38 25 -113No.
40 50 Stroke[mm] Origin 50mm Motor side End side 10 20 30 40 50 60 Stroke[mm] Origin 50mm Motor side End side -50 -40 -30 -20 -10 0 Stroke[mm] Origin 50mm Motor side End side -40 -30 -20 -10 0 10 Stroke[mm] Origin 50mm Motor side End side -60 -50 -40 -30 -20 -10 Stroke[mm] -29- 4.
Speed[mm/s] Stroke Range 701 to 800 20 to 550 12 to 330 6 to 180 3 to 90 24 to 750 16 to 500 8 to 250 4 to 125 30 to 1140 20 to 760 10 to 350 5 to 175 801 to 900 24 to 610 16 to 410 8 to 200 4 to 100 30 to 930 20 to 620 10 to 280 5 to 140 Actuator specification 901 to 1000 24 to 500 16 to 340 8 to 170 4 to 85 30 to 780 20 to 520 10 to 250 5 to 125 1001 to 1100 30 to 660 20 to 440 10 to 220
Tightening torque 0.3 to 0.4Nm Washer Connector assembly part numbers Grommet (rubber) Housing SY100 30 4A For DC: (Light mounting location) (Rating symbols) See table below Lead wire length Without lead wires: SY100 30 A (Connector, socket x 2pcs. only) Terminal block 300mm 600mm 1000mm 1500mm 2000mm 2500mm 3000mm 5000mm For DC SY3160-5LO-M5 SY100-30-4A-20 Nil 6 10 15 20 25 30 50 Terminal
40 50 CCW CW Stroke[mm] Origin 50mm 10 20 30 40 50 60 CCW CW Stroke[mm] Origin 50mm -50 -40 -30 -20 -10 0 CCW CW Stroke[mm] Origin 50mm -40 -30 -20 -10 0 10 CCW CW Stroke[mm] Origin 50mm -60 -50 -40 -30 -20 -10 CCW CW Stroke[mm] -25- 4.
External Connections . 30 5.1 PWR: Power supply connector . 30 5.2 MOT: Motor connector, ENC: Encoder connector . 30 5.3 SI: Serial I/O Connector . 30 (1) Connecting the teaching box . 30 (2) Connection with a PC . 31 5.4 CC-Link communication connector . 31 6.
5F () Sub Function 9.5.1 1 F0 (P.30) 2 F0 Address 9.5.1 (P.30) 3 F0 Address(0) 0 4 F0 DATA(H) 9.5.1 (P.30) 5 F0 DATA(L) 6 F0 7 F0 815 F0 H= L= 46 - 11
Make sure to allow intervals of 15 ms or longer (30 ms is recommended) between input signals, and maintain the input state for the same period of time. 30 No.JXC-OMY0002-A -Output terminalNo. Function Description B1 OUT0 When the operation is started and DRIVE is turned OFF, a Bit no. corresponding to the number of the active step data will be output from these terminals.
Leave an interval of a minimum of 15 ms (recommendation is 30 ms) between input signals and maintain the state of the signal for a minimum of 15 ms (recommendation is 30 ms), because PLC processing delays and controller scanning delays can occur. 12.4 Controller input signal response Signal timing Check the timing of the signal from the PLC to the controller. time When power is applied,
Note) Apparent power (VA) [Current mA] AC Holding 3.5/50 Hz, 3/60 Hz 100 VAC: 35/50 Hz, 30/60 Hz 200 VAC: 17.5/50 Hz, 15/60 Hz Surge voltage suppressor Indicator light DC: Diode, AC: ZNR DC: LED (Red), AC: Neon bulb Option Part no.
Not required Unrestricted 150/30 Note 1) Be certain that pressure within operating pressure range be supplied to supply port, because return pressure is introduced from supply port {1(P)} for activation. Note 2) Impact resistance: No malfunction resulted from the impact test using a drop impact tester.
Operation methods 30 8.1 Outline 30 8.2 Operation by Step No. 30 8.3 Position/speed monitor 30 8.4 Operation by numerical instruction 30 9. Memory map 31 9.1 Memory allocation 31 (1) Input Area Mapping 31 (2) Input area details 32 (3) Output area mapping 36 (4) Output area details 37 (5) Record data (request sent from PROFINET master to JXCPH controller) 41 10.
Product Outline . 15 4.1 System construction . 15 4.2 Setting Function . 16 4.3 Step data setting method . 19 4.4 Parameter setting method . 30 5. Wiring of cables / Common precautions . 33 6.
Inappropriate specifications Leave an interval of a minimum of 15 ms (recommendation is 30 ms) between input signals and maintain the state of the signal for a minimum of 15 ms (recommendation is 30 ms), because PLC processing delays and controller scanning delays can occur. 8.4 Controller input signal response Move occasionally Signal timing Check the timing of the signal from the PLC to
LEY40#EA: 9 kg, LEY40#EB:19 kg, LEY40#EC:38 kg LEYG40#EA:7 kg, LEYG40#EB:17 kg, LEYG40#EC:36 kg 10 mm minimum Door (Lid) 30 mm minimum Controller 60 mm minimum 30 mm minimum (direct mounting) 50mm or more (DIN rail mounting) Controller Caution If the mounting surface for the controller is not flat or is uneven, excessive stress may be applied to the enclosure, which can cause failure.
It is necessary to set it on the PLC side according to the kind of PLC. 6.2 The recommended value of the parameter [LEJ] LEJS40 LEJS63 LEJB40 LEJB63 Lead symbol H A B H A B T Series Lead 24 16 8 30 20 10 27 42 Parameter *1,*2 Para.
It is necessary to set it on the PLC side according to the kind of PLC. 6.2 The recommended value of the parameter [LEJ] LEJS40 LEJS63 LEJB40 LEJB63 Lead symbol H A B H A B T Series Lead 24 16 8 30 20 10 27 42 Parameter *1,*2 Para.