Title not found port size (inch) A, B port size (metric) spaEleyonamanr'od Manifold D-sub Connector .
AREA A position 2 The AREA signal is output commonly for the ranges set for both the AREA A and AREA B. AREA B Set as AREA 1 AREA 2. position 1 AREA B position 2 48 - Data (Saved data) Data is sent as hexadecimal numbers.
A B A B A B How to Mount and Move the Auto Switch How to Mount and Move the Auto Switch Flat head watchmakers screwdriver Auto switch mounting screw (M2.5 x 4 l) Accessory Auto switch mounting nut M2.5 x 4 l 5 to 6 Note) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
B) Under the above conditions, adjust shim so that the space between the workpiece and the clamping block is about 0 mm. Theoretically there is no clamping force for holding a workpiece under this condition. C) In order to generate clamping force from the state described in step B, insert additional shim.
Position 2 The AREA signal is output for both the AREA A and AREA B set configuration. AREA B Set as AREA 1AREA 2. Position 1 AREA B Position 2 21 (2) Step Data Save Command "EU" Details Use after executing Step Data setting comand "EE".
Auto switch a c b d Proper Mounting Position (mm) D-Z7/Z80 D-Y59/Y7P D-Y69/Y7PV D-Y7W D-Y7WV Auto switch model D-M9 D-M9V D-M9W D-M9WV D-A9 D-A9V Proper Mounting Position (mm) A B A 15 19.5 24.5 B A 14 18.5 23.5 B Bore size 63 80 100 a b 14 18 17 c 20 24 23 d Auto switch model 15 18 22.5 19 23.5 28.5 11 14 18.5 10 13 17.5 D-A9 D-M9 D-M9W 2 6 5 8 12 11 Note) Adjust the auto switch after confirming
. 2016 SMC Corporation All Rights Reserved VP4*50*-OMC0001-B
In that case, loosen the screw (3f) and place a lead wire into the bracket (3d), and then tighten it once again. b) The maximum size for the round terminal (9) is 1.25 mm2 3.5 and for the Y terminal is 1.25 mm2 4. c) Cable (8) outside diameter: 6 to 12 mm Note) For the one with outside diameter ranged between 9 to 12 remove the inside parts of the rubber seal (7) before using. 3.
. 2018 SMC Corporation All Rights Reserved VT317-OMH0002-B
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
(Part1:General requirements) ISO 10218-1992:Manipulating industrial robots -Safety JIS B 8370: JIS B 8361: JIS B 9960-1:-((1 :) JIS B 8433-1993: 2) : : : 1 2. 3. 1. 2. 3. 4. 2 No.LFE*-OMY0008 / 1 1.5 3 3) 1 1 () [] 3 No.LFE*-OMY0008 () () () () 4 No.LFE*-OMY0008 () * (100 20 ) () <> 2MPa 5 No.LFE*-OMY0008 * (1623 ) FG (49N ) () M12 IN IN OUT OUT OUT OUT () 6 No.LFE
Circulating fluid return port When heating the circulating fluid, the high-pressure, high-temperature refrigerant gas is bypassed into the evaporator by expansion valve B to heat the circulating fluid. The combination of the precise control of expansion valve A for cooling and expansion valve B for heating allows for high temperature stability.
8370: JIS B 8361: JIS B 9960-1: 1 ) JIS B 8433-1993: *2) 1. 2. 3. 1. 2. 3. 4. 2 VP4_50-OMU0001 / 1 1.5 *3) *3)1 1 () 3 VP4_50-OMU0001 VP4*50, VP4*70, VVP4*0 Series 5 / () () () () 0.1 2 3 VP4350 C-R ( )C-R 3 ( DC 5% AC 15% ) (SSRTRIAC )AC 1) 3 (C-R ) OFF 2)() ZNR 1V 4 VP450-OMU0001 VP4*50, VP4*70, VVP4*0 Series 5 / ( ) (1) ()COMCOM (2) () Sol.1: Sol.2: 1.NPN Sol
CDA2 B 50 200 X1184 B31J S With built-in special magnet Number of auto switches Cylinder stroke Description 2 pcs. 1 pc.
S: B Throo h hole standard A Both ends ta d L Foot mount F Rod side Iia e Head side flan e Type of Auto Switch , No auto SWitch built in (high magnetic Bore Size D Clevis mount . ~ field resIstance ma net 50 50mm P7G 0P10 63 63mrn l'l14C D-P74 80 80mm i P7 D-P75 Cylinder Stroke D-PS P8!