Auto Switch Guide (Tightening torque of M3 screw should be 0.5 to 0.7 Nm.) Auto Switch Mounting Bracket Part No.
M3 x 0.5 x 3L M8 x 1.25 x 8L (Bolt holder) (Hexagon socket head set screw) 31 0.5 45 45 3 3 5.3 5.3 250.2 250.2 16 32 2-M3 x 0.5 through 6.5 counter bore depth 5 (Same on the opposite side) 3.4 through 3 3 45 45 5.5 M2.5 x 0.45 x 6L (Cap screw) M3 x 0.5 x 12.5L (Hexagon bolt) and M3 x 0.5 (Hexagon nut) 2-M3 x 0.5 through Steel ball Plug 2-M3 x 0.5 through 2.75 (11) (10+ST) 250.2 4 Part no
(Tightening torque of M3 screw should be 0.5 to 0.7Nm.) tModification of the detecting position should be made in the condition of e.
/ISE20 Series Function Details ZSE20C(F)/ISE20C(H) ZSE20B(F)/ISE20B ZSE20B(F)-L/ISE20B-L ZSE20A(F)/ISE20A ZSE20(F)/ISE20 Function Details Display examples of the main and sub (set value) screens of each mode.
(Unit number 1 to F is vaild when used the Modbus communication) Never touch the power switch with wet hands to avoid electrical shock. (Min. increment) Default whether or not an alarm has occurred. 0 to F 4 Unit Number (Hex decimal) 0 Target Temp. Sets target temp. for control. 10.0 to 60.0C 2) Confirm that the panel are free from dust.
Cooling capacity (Set temperature 25C and ambient temperature 25C) Approx. 200W Approx. 400W Approx. 510W Approx. 800W Approx. 1000W (Flow rate 3L/min) (Flow rate 3L/min) (Flow rate 3L/min) (Flow rate 4L/min) (Flow rate 4L/min) Circulating fluid Water, Ethylene glycol solution up to 20% The compatibility of equipment is the responsibility of the person Tank capacity Approx.1.3L who designs
INNER VALVE(B) LOCK NUT (261020) INNER VALVE (A) (M3) (26102) 251 INNER VALVE Assy (26100-6) -8- 7.Countermeasures for failure ! Warning Avoid use when failure is not solved. Phenomenon Cause Countermeasures Dust attach supply port or exaust port Disassemble and clean. (If flawed, replace the part.)
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
J r + ' + t i t t t t t l t | l , b o r j | | | , ' l l l " ' r e , l l l t t l Sealtype . | | E ' r l Valve s-port Body Ported liT T.T""n l l l l E f f i . I r F I l f f i r ] Pilot valve specifications I I il*d*drffir -.
C u t o f f M O D E < 7 0 . 0 C sensor (Ex. : 70.0 C). Function : Sets upper limit of temp. which the internal temp. sensor detects and judges the unit should be shut off. When the temp. set in this item is reached, the alarm [ERR12] arises. L o w T e m p . C u t o f f 9. Low Temp.
Or for applications in which a pneumatic speed controller suffices (3l/min).
If a higher flow rate is supplied, the cooling and heating capacity will be slightly affected, but a flow rate of lower than 3L/min will impair the cooling and heating capacity significantly. Be sure to avoid operating the product without cooling water or with cooling water at extremely low flow rates.
0.2% of full span Repeatability Within 0.5% of full span Linearity Within 1% of full span Note 3) Bleed port: 9.5l/min (ANR) or less (supply pressure: 1.0MPa) Exhaust port: 2l/min (ANR) or less (at maximum set pressure) Bleed port: 9.5l/min (ANR) or less (supply pressure: 1.0MPa) Exhaust port: 2l/min (ANR) or less (at maximum set pressure) 4l/min (ANR) or less (supply pressure: 1.0MPa) 3l
Panel mount adapter ZS-46-B Panel mount adapter + Front protection cover ZS-46-D Lead wire with connector ZS-46-3L 3-core, 2 m, Non-waterproof (Without waterproof cover) Front protection cover ZS-27-01 D Panel mount adapter + Front protection cover ZS-46-D R1/8 Piping adapter ZS-46-N1 NPT1/8 Piping adapter ZS-46-N2 9
Panel mount adapter ZS-46-B Panel mount adapter + Front protection cover ZS-46-D Lead wire with connector ZS-46-3L 3-core, 2 m, Non-waterproof (Without waterproof cover) Front protection cover ZS-27-01 D Panel mount adapter + Front protection cover ZS-46-D R1/8 piping adapter ZS-46-N1 NPT1/8 piping adapter ZS-46-N2 7
Other parameter settings Item Page Default setting [F 3] Response time page 30 2.5 ms [F 4] Display resolution page 31 1000-split [F 5] Auto-preset function page 32 Manual [F 6] Fine adjustment of display value page 34 0% [F 7] Power saving mode page 35 OFF [F 8] Security code page 36 OFF [F90] Setting of all functions page 37 OFF [F97] Copy function page 39 OFF [F98] Check of output page