The angle adjustment range can be changed within the 0° to 100° range as a special order.<br>Select the desired range (“-XC12” to “-XC15”) and add the corresponding suffix to the end of the CDRQ2BSP40-90 part number. Check the catalog for details on the “-XC12” to “-XC15” suffixes as the position of the start and end points vary.

In addition to the solenoid valve and air operated types, there are also variations for normal temperature use (up to 60°C) and high-temperature use (up to 100°C) as well as a wide variety of port sizes available (20A to 100A). <br>In addition, controllers for turning multiple VXF series valves ON/OFF are also available.

<br>The higher the number, the finer the filtration accuracy. <br>The adaptation with the nominal filtration rating of SMC elements is as follows: #100 mesh ― 149 μm, #150 mesh ― 105 μm, and #200 mesh ― 74 μm.

5 Port Solenoid Valve Series SY3000/5000/7000/9000

rate: 50% Stroke 300 mm Series MB, CA2 Pressure 0.5 MPa Load rate: 50% Stroke 500 mm Average speed (mm/s) Series 800 700 600 500 400 300 200 100 0 Perpendicular, upward actuation SY3140-01 Horizontal actuation 800 700 600 500 400 300 200 100 0 SY5140-02 800 700 600 500 400 300 200 100 0 SY7140-03 800 700 600 500 400 300 200 100 0 SY9140-04 Cylinder is in extending.

Table of Contents

Possible to use in vacuum to 100 kPa Tubing material Tubing O.D.

Brake mechanism added

75 100 80 100 90 100 2 D-A3C D-G39C D-K39C 20 + 35 (n 2) (n = 2, 3, 4, ) 75 + 35 (n 2) (n = 2, 4, 6, 8, ) Note 1) 80 + 35 (n 2) (n = 2, 4, 6, 8, ) Note 1) 90 + 35 (n 2) (n = 2, 4, 6, 8, ) Note 1) (Different surfaces) 2 n 100 + 100 (n 2) (n = 2, 3, 4, 5) 100 + 100 (n 2) (n = 2, 4, 6, 8, ) Note 1) (Same surface) 1 10 75 80 90 (Different surfaces) (Same surface) 20 55 75 80 90 75 + 35

Vacuum Unit

V V F V None (SI unit only) H V V J V None (SI unit only) P Pressure sensor 0 to 101 Analog output 1 to 5 V T 100 to 100 N Without pressure switch for vacuum/pressure sensor 100 to 100 r Connector (Supply valve/Release valve/Pressure switch for vacuum) For supply valve/release valve: 300 mm (Connector assembly)4 For pressure switch for vacuum: 2 m (Lead wire with connector) Pressure

%silltr

I I I 3.886 4.661 5.436 6.2t1 Table 6.19 Theoretical Air Consumption ot double acting cylinders from 20 to 100 mm dia, in liters per 100 mm stroke Example 1.

SMC Basic Pneumatics

I I I 3.886 4.661 5.436 6.2t1 Table 6.19 Theoretical Air Consumption ot double acting cylinders from 20 to 100 mm dia, in liters per 100 mm stroke Example 1.

KJ

Possible to use in vacuum to 100 kPa Tubing material Tubing O.D.

Wedge Cam Operation Gripper Series MHK2

120 Pressure 0.6MPa 80 100 Pressure 0.6MPa Holding force N Holding force N 0.5MPa 80 60 0.5MPa 0.4MPa 60 0.4MPa 40 0.3MPa 0.3MPa 40 20 20 0.2MPa 0.2MPa 0 0 20 40 60 80 100 20 40 60 80 100 Holding point L mm Holding point L mm 14 14 14 14 14 14 Series MHK2 Wedge Cam Operation Gripper Effective Holding Force: MHKL2 Series Double Acting The holding force shown in these tables represents the

KQ2

(100) 71 (71) 44.5 46 112 116 16 Reference dimensions after R thread installation.

Air Fittings & Tubing

(100) 71 (71) 44.5 46 16 Reference dimensions after R(PT) thread installation.

Vacuum Ejector Series ZM

/110 VAC (50/60 Hz) Vacuum DC: 1 W (With light: 1.05 W), 100 VAC: 1.4 W (1.45 W), 110 VAC: 1.45 W (1.5 W) Mass Made to Order (Refer to pages 1004 to 1006 for details.)

CEx-OMB0060

Input of reset signal from PLC/ PC shall be between 10 ms and 100 ms. For longer input time, processing takes approximately 150 ms from startup of reset signal and it increases total reset processing time.

HEC-OM-R008

HECR002: 100 to 240VAC HECR004: 100 to 240VAC HECR006: 100 to 240VAC HECR008: 100 to 240VAC HECR010: 200 to 240VAC DC output voltage of product is reduced. 2) Confirm that the heat sink and panel are free from dust.

Pneumatic Purification

They should always br preceeded by AM series.

CEx-OMQ0011

100 50 50 0 0 0 5 m/s m/s 19 4-3.

HEC-OM-U015

No temperature decrease when 100% cooling output. No temperature increase when 100% heating output. Cooling or heating capacity overload. Abnormal If the volume of circulating fluid system is too large, the change of temperature takes a long time. In this case, change overload judging time setting to avoid this alarm.

HEC-OM-Y008

Read this manual before using the product, to ensure correct handling, 300 300 The production serial number code printed on the label indicates the year and month of production as per the following table: 200 200 Ambient temp. 35 deg.C After shutting down the power supply, ensure a time interval at least and read the manuals of related apparatus before use. 100 Ambient temp. 35 deg.C 100