SYJA3000 (A) 4 (B) 2 (A) 4 (B) 2 0.6 SS5YJA5 The remainder of the manifold part number is called out the same as an SS5YJ5 0.5 1 (P) 3 (R) 1 (P) 3 (R) Pilot pressure range 3 position pressure center 0.4 (A) 4 (B) 2 Specify the part numbers for the valve(s), blank plate assembly and manifold base. 0.3
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
L4 L4 L5 A L5 D3 D3 T T D2 L1 D2 L1 L2 L2 AS ASP Metric Size ASN A M1 L5 Max.
Model d T Weight (g) H D1 D2 L1 L2 L3 L4 A Max.
Seal Tube Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0 MPa The use of a special profile ensures sealing and reduces resistance when the tube is inserted. Body (White) O-ring Stud Effective when piping in a confined space. The body and the threaded portion can rotate. PAT.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
Bulkhead union P. 60 KCE Use to connect tubes through a panel. One of two ports has a self-seal function. Bulkhead connector P. 60 KCE Use to connect male thead and tube through a panel. 15-2-67 Series KC Precautions Be sure to read before handling.
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
Cracking pressure is a pressure at which the valve starts opening and not a pressure at which the valve is fully open. 15-8-7
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
Teodoro Garcia 3860 (1427) Buenos Aires, Argentina TEL: 011-4555-5762 FAX: 011-4555-5762 SWITZERLAND SMC Pneumatik AG Dorfstrasse 7, Postfach 117, CH-8484 Weisslingen, Switzerland TEL: 052-396-3131 FAX: 052-396-3191 BOLIVIA SMC Pneumatics Bolivia S.R.L.
In order to prevent a malfunction or diaphragm damage caused by debris or cutting chips in the fluid, install a filter with approximately 100 mesh on the inlet side of a flow switch. C (COM) A (N.O.) Color of lead wire Black Symbol Contact C Z I SE3 Common A White Normally Open B (N.C.)
Teodoro Garcia 3860 (1427) Buenos Aires, Argentina TEL: 011-4555-5762 FAX: 011-4555-5762 SWITZERLAND SMC Pneumatik AG Dorfstrasse 7, Postfach 117, CH-8484 Weisslingen, Switzerland TEL: 052-396-3131 FAX: 052-396-3191 BOLIVIA SMC Pneumatics Bolivia S.R.L.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
A unique positioning mechanism allows accurate installation and removal of tubing with ease even in a hardto-see locations, while preventing piping errors when reconnecting. Plug Holder Socket Plug case Irregular shape permits engagement in a proper position.
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.
Teodoro Garcia 3860 (1427) Buenos Aires, Argentina TEL: 011-4555-5762 FAX: 011-4555-5762 SWITZERLAND SMC Pneumatik AG Dorfstrasse 7, Postfach 117, CH-8484 Weisslingen, Switzerland TEL: 052-396-3131 FAX: 052-396-3191 BOLIVIA SMC Pneumatics Bolivia S.R.L.
Can be used for a wide range of pressures from low vacuum up to a pressure of 1.0 MPa. The use of a special profile ensures sealing and reduces resistance when the tube is inserted. Guide Collet Can be used in copper-free application. Body O-ring Flame resistance (Equivalent to UL-94 standard, material V-0) Stud Tube Effective when piping in a confined space.
Note 5) Without a valve function. Note 6) For NPT thread type.