VY511, VYU5 SW RESET RUN2 RUN1 OV INPUT 6 7 5 8 4 + 9 3 SET UP A 2 B 1 0 C D 1 E F 0 to 10V V R 1 OUTPUT SET UP BALANCE CONTROLLER VYU5-D 2 V R 2 OV ERR.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Calculate the moment of inertia for A and B separately as shown in the figures on the right. A part B part Procedure Calculation Calculation example 1. Check the operating conditions, dimensions of attachment, etc. Operating model: MHY2-16D Opening time: 0.15 s a = 40 (mm) b = 7 (mm) c = 8 (mm) d = 5 (mm) e = 10 (mm) f = 12 (mm) A part a b c B part e f d 2.
Be sure to adopt a reliable connecting method if the rotary table is used very frequently or if it is used in a location that is exposed to a large amount of vibrations. Consider the possibility of a reduction in the circuit air pressure caused by a power failure.
Be certain to adopt a reliable connecting method if the rotary actuator is used very frequently or if it is used in a location that is exposed to a large amount of vibration. Consider the possibility of a reduction in the circuit air pressure caused by a power failure.
A Model Mounting Auto switch operating range A B A B A B 54 MXY6 34 MXH 59 5 MXY8 39 MXU 67 MXY12 47 MXS Solid State Auto Switch D-M9B(V), D-M9N(V), D-M9P(V) Lead wire entries inside MXQ (mm) B B Model Mounting Auto switch operating range MXF A B A B A B 50 MXY6 3 38 MXW 55 MXY8 3.5 43 MXJ 63 MXY12 3 51 MXP Lead wire entries parallel 2-Color Display Solid State Auto Switch D-M9BW(V), D-M9NW
10VA 5W AC1500V1 AC500V 1 DC500V50 0+50 3585RH 1500V600V Hz 2 10G XYZ 3 250g 6 6 6 6 6 6 6 6-1 1 1 1 (DC12V60mA) B A G N D A B COM RS COM COM 12V G N D A B COM OUT1 AC100V OUT2 COM COM OUT3 COM DC24V GND AC100V (C E U 1) (C E U 1-D ) CEU1 +12V + 12V 1 A 680 CO M +12V + 12V 1 B 680 COM +12V D C 1 2 V60 m A GND RS COM FG AC100V 6 6 6 6-3 3 3 3 1C E U 1 CE1-R**
85%] [1055Hz 0.75mmXYZ 2 ] 7-2 7-2-1 AC100V15AC85VAC115V 50/60Hz DC24V100.4A 2 0.75mm 2D FG0.75mm 100 FG FG 7-2-2 5m 20m5m20m CE1-H0374 22 CE1-R 20m 200m 5m 20m * A DC12V 0.3A B AWG24 DC12V 0.3A CEU2 CE2 U 25mm 400 200mm 1 R25 100 / 23 7-3 7-3-1 2 (AC100V,15%) 1 24V10%,0.4A) 4 CEU2 3 2 1 END / 1. 2.
Stainless Steel Cylinder Se ries CG5-S 20, 25, 32, 40, 50, 63, 80, 100 How to Order X165US TN CG5 L N 25 S R 100 Without Auto Switch X165US TN CDG5 L N 25 S 100 G5BAL R With Auto Switch Inch rod thread (Only available with "TN" port option. Currently only available on the 20 to 63mm bore sizes.)
Body Size: 5000, Port Thread: Rc, Port Size: 10 (1), Option: None, Voltage: 5 (24 VDC), Electrical Entry: D (Type D, DIN Terminal w/Connector), Surge Suppressor: Z (with Light/Surge Voltage Suppressor), Flow Direction, Pressure Unit: R (Flow Direction: Right to Left)
GR-S-010(10g) GR-S-020(20g) 6 - R/L side parallel type LEKFS16 18 26 25 Component Parts No. Description Material Note No.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.
Atmospheric release port Air tube Recommended tubing (P/A) TU0425 (polyurethane)
Pressure Momentary change P1 P2 Set value Anti-chattering function Devices such as large bore cylinders and high-flow vacuum ejectors consume a large volume of air when they operate, and this may cause a momentary drop in the primary pressure.
A digital computer/controller used for automation of electromechanical processes. R Reboot Unless otherwise noted, the term reboot in this document means that the MPC must be power cycled. The specified position which the MPC has been directed to maintain. Setpoint may be specified via a setpoint sent from a PLC.
Avoid using in a closed place without ventilation. h. Avoid using in direct sunlight or radiated heat. i. Avoid using in a place where there is a strong magnetic noise (strong electric field, strong magnetic field, or surge). j. Avoid using in a place where static electricity is discharged to the body. k. Avoid using in a place where a strong high frequency occurs. l.