CRJ Thin rectangular plate (rectangular parallelopiped) Position of rotational axis: Perpendicular to the plate through one end (also the same in the case of a thicker plate) + m x a + K 3 a1 I = m x (Example) When the shape of m is a 12 4a2 + b I = m1 x + m2 x 12 4a1 + b 5 2r sphere, refer to 7 above. K = m x 5. Thin rectangular plate (rectangular parallelopiped) 10.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.
port} VQZ200 VQZ300 Symbol Port size V100 Nil Without sub-plate Rc 1/8 Rc 1/4 Rc 3/8 01 02 03 SY Type of actuation SYJ (A) 2 N.C.
Nijverheidsstraat 20 B-2160 Wommelgem Belguim TEL: 03-355-1464 FAX: 03-355-1466 TAIWAN SMC Pneumatics (Taiwan) Co.,Ltd. 17, Lane 205, Nansan Rd., Sec.2, Luzhu-Hsiang, Taoyuan-Hsien, TAIWAN TEL: 03-322-3443 FAX: 03-322-3387 POLAND SMC Industrial Automation Polska Sp.z.o.o. ul.
Nijverheidsstraat 20 B-2160 Wommelgem Belguim TEL: 03-355-1464 FAX: 03-355-1466 TAIWAN SMC Pneumatics (Taiwan) Co.,Ltd. 17, Lane 205, Nansan Rd., Sec.2, Luzhu-Hsiang, Taoyuan-Hsien, TAIWAN TEL: 03-322-3443 FAX: 03-322-3387 POLAND SMC Industrial Automation Polska Sp.z.o.o. ul.
For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that cannot vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that can not vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that cannot vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Note) Component parts Aoolicable manifold base MBF261--3;-18 M a n i i o l d b l o c k O , C l a m p O ' O o r i n g O ' O ' O ' O Adapter O , Pin housing. Guide. Insertllug lead wire Plug-in type Connector lead wires o Manilold block assy ' :o-side ports A, B l-1l8 P A, B bottom 2-1l8 P, A, B bottom w/ (114 A, B side) MBF261.-3r-1A M a n i f o l d b l o c k O , C l a m p O , @ .
Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.
Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.
flow rate of 14.1 scfm [400 L/min] (ANR) is P1 29 psi (0.2 MPa) for a 4 orifice and P1 84 psi (0.58 MP)a for a 3 orifice.
x 20 /C1 7 x 45o 7 x 45o 22.5o 22.5o A A A A 166p0.2 178p0.2 A-A A-A The surface roughness of the orifice machining should be Rz6.3 or less.
, are Nil, A, B, D, E, Z. 3 Available for air and water. 270 IN OUT C 3 A 3 A 6 D 1 Available for the VXZ A to 2 .
Example) AW30-03C-2R-X2622A y t r e w q Stainless steel 316 specification Symbol Description K q Body size 30 40 IP K w Thread type Nil Rc N NPT F G + IW 02 1/4 03 3/8 04 1/2 06 3/4 + 1301 K e Port size AW AW IL1 K r Option i a Float type auto drain Nil Without option C Note 1) Float type auto drain (N.C.
In case of facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.