VT325 Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
Do not supply air pressure from other ports than 1(P) port. Air leakage may occur when the pressure is supplied from other ports. 1. Ensure connection so that air is supplied to the port 1(P) port. Air leakage may occur when the pressure is supplied from other ports. 2.
Do not use in an environment, where water or oil is splashed. Because it is the open type construction. If water or oil were to make an ingress, the electrical circuit would be corroded and result in a malfunction or damage. 2. Operating fluids are either air or inert gas exclusively. Never use liquids. 3. Never use in an environment where flammable fluid or gas is used.
120 VAC (50/60 Hz) 4 220 VAC, 50/60 Hz 5 24 VDC 6 12 VDC 7 240 VAC, 50/60 Hz 9 Other Option Option Non-locking push type (Flush) Non-locking push type (Extended) Locking type (Tool required) Locking type (Lever) Nil For VFS130 G GS Grommet Grommet with surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor D DZ DIN terminal Common pilot exhaust 22 A B DO
flange Head flange Single clevis Double clevis Center trunnion Change of rod end shape Heat resistant cylinder (150C) Rod end nut Clevis pin With heavy duty scraper Standard Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel -XC7 Piston rod ball joint Rod clevis Rod boot Option -XC10 -XC11 -XC22 -XC35 Dual stroke cylinder/Double rod type Dual stroke cylinder/Single rod type Do
Accessories Basic Foot Rod end flange Head end flange Center trunnion Single clevis Double clevis Mounting Rod end nut Standard Clevis pin Piston rod ball joint Option Rod clevis Rod boot Please do not use a piston rod ball joint (or floating joint) together with a head end clevis with a ball joint (or angled head end clevis with a ball joint). 20
Do not scratch or dent the air gripper by dropping or bumping it when mounting. Slight deformation can cause inaccuracy or a malfunction. 3. Tighten the screw within the specified torque range when mounting the attachment. Tightening with a torque above the limit can cause malfunction, while insufficient tightening can cause slippage and dropping. 1.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Note) Do not apply rotational torque to the piston rod. When the stroke reading cylinder is used near a motor, welding machine or other source of noise generation, there is a possibility of miscounting. In this case, noise should be suppressed as much as possible and the following countermeasure should be taken. 1. Connect the shield wire to FG (flame ground). 2.
Function: 1 (2 Position Single), Body Option: 20 (Body Ported/Individual Pilot EXH), Pilot: Internal Pilot, Voltage: 6 (12VDC), Lead Wire: DO (DIN Connector w/o Connector), Surge Suppressor: None, Manual Override: B (Locking Slotted Style), Piping: Side, Port Size: 01 (Base Mounted w/Sub-plate 1/8, Body Ported 1/8), Thread: F (G), Option: F (Foot Bracket)
Since PE port is the exhaust port of the pilot valve, do not attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
/Single Unit), Solenoid Valve Option: Brass Body, NBR Seal, Class B, Suffix: Standard, Port Size: 03 (3/8), Thread Type: N (NPT), Voltage: 3 (110VAC 50/60HZ), Electrical Entry: DO (DIN w/o Connector), Full-wave Rectifier: R (w/Full-wave Rectifier)
To verify the gripping condition or to make any adjustments, make sure to do so in an area where the air gripper or the workpiece will not fall. Opening/Closing angle (Both sides) 646 A Series MHT2 Toggle Type Air Gripper Construction w o i u !0 !1 Component Parts No.
Axial Mounting Lateral mounting How to Mount the Attachment to the Finger Body tapped (1) Make sure that the piston rod is retracted so as not to apply undue strain on the piston rod while an attachment is being mounted to the finger. (2) Do not scratch or dent the sliding portion of the piston rod.
Do not scratch or dent the air gripper by dropping or bumping it when mounting. Slight deformation can cause inaccuracy or a malfunction. 2. Tighten the screw within the specified torque range when mounting the attachment.
Function: 1 (2 Position Single), Body Option: 10 (Non Plug-in Type Sub-plate, Standard), Pilot Type: Internal Pilot, Voltage: 3 (110~120VAC 50/60HZ), Lead Wire: DO (DIN Connector w/o Connector), Surge Suppressor: Z (Light & Surge Suppressor), Port Size: 06 (Sub-plate Plug-in Terminal 3/4, Non Plug-in Standard 3/4), Thread: N (NPT)
Function: 1 (2 Position Single), Body Option: 10 (Non Plug-in Type Sub-plate, Standard), Pilot Type: Internal Pilot, Voltage: 3 (110~120VAC 50/60HZ), Lead Wire: DO (DIN Connector w/o Connector), Surge Suppressor: Z (Light & Surge Suppressor), Port Size: 06 (Sub-plate Plug-in Terminal 3/4, Non Plug-in Standard 3/4), Thread: T (NPTF)
Function: 2 (2 Position Double), Body Option: 10 (Non Plug-in Type Sub-plate, Standard), Pilot Type: Internal Pilot, Voltage: 5 (24VDC), Lead Wire: DO (DIN Connector w/o Connector), Surge Suppressor: None, Port Size: 06 (Sub-plate Plug-in Terminal 3/4, Non Plug-in Standard 3/4)
Function: 1 (2 Position Single), Body Option: 10 (Non Plug-in Type Sub-plate, Standard), Pilot Type: Internal Pilot, Voltage: 3 (110~120VAC 50/60HZ), Lead Wire: DO (DIN Connector w/o Connector)
Function: 1 (2 Position Single), Body Option: 10 (Non Plug-in Type Sub-plate, Standard), Pilot Type: Internal Pilot, Voltage: 3 (110~120VAC 50/60HZ), Lead Wire: DO (DIN Connector w/o Connector), Surge Suppressor: Z (Light & Surge Suppressor), Port Size: 10 (Sub-plate Plug-in Terminal 1, Non Plug-in Standard 1), Thread: N (NPT)