VXF Rated voltage Electrical entry 2 200 VAC 50/60 Hz 1 100 VAC 50/60 Hz G Grommet C Conduit 3 110 VAC 50/60 Hz D DIN terminal 4 220 VAC 50/60 Hz T Conduit terminal 5 24 VDC Refer to the table (1) given below for availability. 6 12 VDC 7 240 VAC 50/60 Hz 8 48 VAC 50/60 Hz 9 Other (Contact us for inquiry) Refer to the table (1) given below for availability.
When a system hazard can be expected due to a drop in vacuum pressure caused by power loss or vacuum pump trouble, install a safety circuit and configure the system so that it can avoid the danger. 2. When a system hazard can be expected with a malfunction of the vacuum regulator, install a safety circuit and configure the system so that it can avoid the danger. 1.
When ordering a valve with a lead wire of 600 mm or longer, be sure to indicate the model number of the valve without connector and connector assembly. A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 4-12-4 5 Series VQ100 Precautions Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
When ordering a valve with a lead wire of 600 mm or longer, be sure to indicate the model number of the valve without connector and connector assembly. A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 4-12-4 Series VQ100 Precautions Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
When ordering a valve with a lead wire of 600 mm or longer, be sure to indicate the model number of the valve without connector and connector assembly. A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 4-12-4 5 Series VQ100 Precautions Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
A A A A 90 B A B A B A B A Dimensions are the ones for SV1300--.
However, when a workpiece is permeable or has a rough surface, note that the vacuum pressure drops since the workpiece takes air in. In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
However, when a workpiece is permeable or has a rough surface, note that the vacuum pressure drops since the workpiece takes air in. In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
However, when a workpiece is permeable or has a rough surface, note that the vacuum pressure drops since the workpiece takes air in. In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
a M MA F NA NA F K A A K C H + Stroke S + Stroke H B ZZ + 2 strokes (mm) Bore size (mm) A a B C d E F G GA J K M MA MM NA P R S T V W H ZZ D 0 -0.018 0 -0.021 0 -0.021 0 -0.021 0 -0.025 0 -0.025 0 -0.025 0 -0.062 0 -0.062 0 -0.074 0 -0.074 0 -0.074 0 -0.074 0 -0.087 40 23 10 60 44 18 45 25 14 17.5 M8 x 1.25 18 13 20 M14 x 1.5 30 1/4 37 114 11 7.5 8 66 246 17 50 25 9 73 53 20 50 28 17 17 M10
Set or correct the product number and mounting orientation of the Card Motor. 14.2 Basic Parameter Setup window (P.60) Unsuitable specification from the Origin position Operating in a strong light source. Check that the Card Motor is not exposed to a strong light source such as direct sunlight. Install a light shielding plate as a cover.
Use this as a standard when mounting, etc. Auto switches have hysteresis similar to micro switches. Use the table below as a guide when adjusting auto switch positions.
/60 Hz) Class B NBR 200 VAC (50/60 Hz) VDW FKM Stainless steel 110 VAC (50/60 Hz) EPDM 220 VAC (50/60 Hz) VQ FKM 24 VDC Note) The armature assembly is a corrosion resistant construction. 12 VDC LVM 6 VDC 5 VDC VCA Nil Thread type 3 VDC Rc Please consult with SMC regarding other voltages.
ZX 36 A VJ10 ZR Rated voltage Lead wire length ZM (Mounting hole) Symbol L (mm) Symbol Rated voltage Lead wire color Nil 6 10 15 20 25 30 1 300 100 VAC 50/60 Hz 110 VAC 50/60 Hz (115 VAC 60 Hz) Blue (2 pcs.)
(Looked by double solenoid valve) (Looked by double solenoid valve) SOL. location B (*) B (*) B B A B A B A B A B A A A A B A B A SOL. location VQC 3 position 3 position Double Double Double Double SI unit Single Single SI unit Single Single SQ Stations 1 2 3 4 5 Stations 1 2 3 4 5 VQ0 The places of asterisk are not used.
P, A port Rc(PT) 107 VEX350 1 2 3 4 123 96 112 26 30 70 90 50 60 25 30 10 15 25 25 80 100 46 60 45 51 60 82 72 95 2.3 , , 1 2.3 VEX370 1 4 Rc(PT)11 4 Rc(PT)1, 1 189 j DIN connector 9 c Bracket 166 h Grommet terminal 175.5 i Conduit terminal g Grommet 110 a Model 130 b 12 d 2 e 47 f 140.5 VEX350 120 VEX370 136 20 5 49 205 9 182 191.5 156.5 5.1-22 VEX3 Body ported/VEX390 Air operated: VEX3900
S Z Without lead wire: (with connector and 2 of sockets only) SY100-30-A Rated voltage R Lead wire length U 5 6 V S R 1 2 24 VDC 12 VDC 6 VDC 5 VDC 3 VDC 100 VAC 50/60 Hz 200 VAC 50/60 Hz 110 VAC 50/60 Hz [115 VAC 50/60 Hz] Nil 6 10 15 20 25 30 50 300 mm 600 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 5000 mm For AC voltage valves there is no S option.
Bore size A002 C A A001 50 63 80 Equivalent to 50 mm Equivalent to 63 mm Equivalent to 80 mm L arm L side position R arm R side position Cylinder port Nil TF NPT G Arm mounting position (A, B, C, D) Note 1) See below Arm Mounting Position. Arm Mounting Position: A, B, C, D A B C D Arm opening angle 30 45 60 75 90 105 120 135 30 45 60 75 90 105 120 135 denotes tool attachment surface.
than a needle throttle of a general purpose cylinder.