SMC Corporation of America
Elite Part Number Search
Search Results "CDQ2B16-15+15DZ-XC10"

Note) Tighten within the tightening torque of 0.5Nm+/-15%. Note: a) Wiring is possible with a bare lead wire. In this case, loosen the screw with washer (3f) and place a lead wire (3d) into the bracket, and then re-tighten the screw. Caution DlN Terminal (Connection) The solenoid is wired with male terminals of DIN connector as shown below.

Neon bulb When 100 VAC or more Coil Note 1) The tightening torque should be within 0.5Nm +/15%. Note 2) Cable (7) external: 6 to 8 mm. Note 3) Crimped terminal like round-shape or Y shape cannot be used.

Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.

.-11 Construction -12 List of valves,options,and Mounting Bolts-13 Electrical Wiring Specifications-14 to 18 F kit -14 P kit -15 T kit -16 L kit -17 M kit -18 Trouble shooting -19,20 -1No.VQC4000V-OMX0001 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.

.* * This time can be shortened as described below. 1) Provide a valve on the outlet side of the membrane air dryer. 2) Supply air with the valve closed so that only purge air flows through the membrane air dryer. 3) After 15 minutes or more, open the valve and let air flow to the outlet side equipment. Selection Caution a. Do not obstruct the purge air discharge ports.

Seal cap 1 pc. seal cap for unused fieldbus interface connector (BUS OUT). 1: For details of suitable cables refer to the Accessories section on page 28. 2: Refer to page 15 for the LED Indication and Settings. -9No.EX-OMN0011-F Installation and Wiring Installation Connect valve manifold to the SI unit.

Seal cap 1 pc. seal cap for unused fieldbus interface connector (BUS OUT). 1: For details of suitable cables refer to the Accessories section on page 34. 2: Refer to page 15 for the LED Indication and Settings. -9No.EX-OMO0030-E Installation and Wiring Installation Connect valve manifold to the SI unit.

Dimensions for installation n: number of valve stations n L 1 2 3 4 5 6 7 8 L1 120.7 136.7 152.7 168.7 184.7 200.7 216.7 L2 80 96 112 128 144 160 176 n L 9 10 11 12 13 14 15 16 L1 232.7 248.7 264.7 280.7 296.7 312.7 328.7 344.7 L2 192 208 224 240 256 272 288 304 (mm) The above table shows dimensions as an example for the SY5000 series valve manifold.

Rc3/8 15 to 20 3. Tighten threads with the proper tightening torque. 6. Piping to products When installing the products, follow the listed torque specifications. When piping to a product, refer to the operation manual to avoid mistakes regarding the supply port, etc. 4. If air leakage increases or equipment does not operate properly, stop operation.

I/O monitor 15 2. Diagnosis Data 24 3. Sys. Configuration 27 4. Parameter Setting 33 5. Terminal Setting 47 Troubleshooting 50 Parameter Setting 52 Specifications 53 Dimensions 53 -1No.EX-OML0011-C Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Applicable cable Tightening torque 0.3 to 0.5 Nm Weight 15 g or less -10No.EX-OMM0008-D Branch connector: For EX9-CCM1 (EX9-CCM3) The branch connector EX9-CCM3 does not come with the product. Item Specification Rated voltage 30 VDC Rated current Power supply: 4 A, Signal: 0.3 A Contact resistance 40 m (The conductor resistance of the cable 40 mm is contained.)

Construction / Parts list, seal list Double acting/ Finger open Single acting / Normal open Single acting / Normal close Double acting / Finger close 5 4 12 7 1 9 10 8 16 15 14 3 2 21 11 18 19 13 20 6 17 Components No. Description Material Remarks Components 12 Needle roller High carbon chromium No.

Do not block the exhaust port of the ejector. 15 - Doc. no. ZQ-OM00801-D Air Supply Use clean air. 1. Using compressed air which contains chemicals, synthetic oils containing organic solvents, salts or corrosive gases, etc. can cause damage or malfunction. Do not use compressed air containing toxic impurities. 2.

If the heater 0 5 10 15 20 25 30 ( temperature is over 200oC or valve temperature is over 150oC, please use thermostat to control the heaters to Time (sec.) Duration of the inrush current flow (as a guide) prevent overheating. With PTC type heaters, there is an initial surge of current (inrush current) after the power is supplied. These inrush current will reduce overtime.

During cushioning or acceleration of the operation start, the variation of stop position is high (as the change in speed is high). 15 - 3-2. Lock release mechanism Operation principle for unlocking mechanism.

When a number is necessary for the connector assembly mark tube, suffix the number to the part no.0 to 15 are provided as mark tube numbers. Ex)+COM spec..

This matches the controller. (2) Check Parallel I/O configuration matches (NPN or PNP). (1) LEL25LT-300 NPN (2) -11- 2.3 Construction 11 8 Motor option with motor cover Motor option with lock 24 3 6 2 4 1 14 22 12 17 13 17 7 B A-A(LEL25LT-) A-A(LEL25MT-) B 19 19 23 5 21 20 16 9 10 15 18 No.

General 3 positions 5 positions General 15 Setting (continue) 1.Stroke adjustment General 3 positions 5 positions General Adjust the stroke of actuating part. 1-1 Loosen fixing bolt, move the unit to the position where required stroke is obtained and fix the unit by the bolt. 1-2 E-MY2C/H Loosen lock nut for adjusting bolt for fine setting of stroke by the bolt.

Seal VCW20-15-6 Note) Order separately. 8 XSA-OMS0001-A Electrical circuit CAUTION [DC Circuit] AC circuit *For AC, the standard product is equipped with surge voltage suppressor.