5 Port Solenoid Valve, Series VQC Example: OMRON Corporation XS2Z-12 4 1 Signal H CAN_H 4 Signal L CAN_L 5 Compatible with DeviceNet specification Micro Style connector.
state timer function for release valve control (timer setting with PLC is unnecessary) Allows sharing of switch/valve power supply, and single line for suction signal (valve wiring is unnecessary) Timer can be easily adjusted without programming Models Standard supply pressure Nozzle diameter (mm) Diffuser construction Air consumption l/min (ANR) Max. suction flow rate l/min (ANR) Model S M H
Make sure whether the operating temperature range, pressure and cleaning solvent type meet the specifications. 25 Fiber element 10 2 0 to 100 0.2 20 50 H Cotton EH 30 75 General cleaning 100 4 Determining the filter model (Nominal) 0 to 100 5 SUS304 M EM1, 2 25 10 Determine the filter model from the element type and the number of elements selected in and , and the housing type selected in
M H D Male elbow Bulkhead union P. 49 KFL P. 51 KFE Use to pipe at right angles to female thread. Most general type. MS Use to connect tubes through a panel. T VMG Union tee Male run tee Use to branch line in the same direction from female thread and in 90 direction. P. 50 KFT KFY P. 51 Use to connect tubes in both 90 directions.
This is not a clean room series product. 4 MACM Series Dimensions W (Workpiece loadable range) 4 x D At maximum offset (A + 2 x S) S F DB DA C X114 X115, X116 U B W A H T H Q PB E PA PD P (Unlocking port) PE P (Locking port) P (Relief port) (Option V only) MACM4, MACM6 MACM2, MACM10 PC PC PC PC PE P (Relief port) (Option V only) PD [mm] Dimensions Model A B C D DA DB E F H P PA PB PC PD
KFG2 MS KKA KP LQ MQR T IDK 165 KS Series Male Connector: KSH (Standard) H (Width across flats) Effective area (mm2) Applicable tubing O.D.
F H L 6mm 10mm 20mm Note) The following options are necessary for operating and setting the controller. LC1-1-S1 PC-98 (MS-DOS) LC1-1-W1 (Windows 95 Japanese) LC1-1-W2 (Windows 95 English) and LC1-1-R (dedicated communication cable) (Refer to pages 80, 81, and 85.)
Note 2) (Nominal size) is not needed as the part number starting with the AL-H is a dedicated number. Note 3) The material of seals (AL-128H-V to AL-137H-V) is EPDM-70. 503 A FH99 Series Replacement parts Handling Precautions Description Part no. Applicable model Connection side: IN Connection side: OUT Set contents q Mounting Confirm IN and OUT before connecting.
Water bath Q = T x V x x C h x 60 x 1000 10 x 2 x 1 x 103 x 4.2 x 103 20C V = 15 x 60 x 1000 After 15 min, = 93.3 W cool 30C down to 20C.
Since it is possible to change the magnetic holding force (from H type to L type), please contact SMC if this is necessary. 5. When disassembling to replace the seals and wear ring, refer to the separate disassembly instructions. Caution 6. Special tools are necessary for disassembly. 6. Apply additional tightening when remounting the head cover after disassembly.
Equipment Uo (or Voc) lo (or Isc) Po Co (or Ca) Lo (La) Ui li Pi Ci + Ccable Li + Lcable If the cable capacitance and inductance are unknown, use the following values: Ccable = 60 pF/ft., Lcable = 0.2 H/ft.
Solenoid valve Rubber seal Pressure differential (MPa) Mist generation (cm3/H) Regulator Series AR Circuit ALD600 ALD900 Pressure differential adjustment valve Pressure differential adjustment valve Flow rate (/min (ANR)) Pressure Differential and Mist Generation Supply oil plug Supply oil plug 2 way valve 2 way valve Oil tank Oil tank Mist generation nozzle Mist generation nozzle Pressure
---Ht-t---t-+-H I--i IN o I w c.
However, note that only the AS221FPQ uses steel. 713 AS-FPQ/FPG Series Dimensions H (Hexagon width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type Applicable tubing O.D. d H (Hexagon width across flats) A L4 D1 L3 D2 M1 L1 T L2 Model Weight (g) (3) Tubing O.D. d T H D1 D2 L1 L2 L3 (4) M1 L4 (1) (4) Max. Min. Max. 1 2 Min.
L6 A Note) Model Applicable tubing O.D. d H Weight (g) D L1 L2 L3 L4 L5 M T Min. Max. Min.
However, note that only the AS221FPQ uses steel. 713 AS-FPQ/FPG Series Dimensions H (Hexagon width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type Applicable tubing O.D. d H (Hexagon width across flats) A L4 D1 L3 D2 M1 L1 T L2 Model Weight (g) (3) Tubing O.D. d T H D1 D2 L1 L2 L3 (4) M1 L4 (1) (4) Max. Min. Max. 1 2 Min.
2 Meter-out type Meter-in type 638 Speed Controller with Indicator/Elbow Type Uni Thread Type AS-FS Series Dimensions: Elbow Type Seal method: Gasket seal For Uni thread Indicator window direction: 0 Indicator window direction: 180 W1 X W2 Y D3 AS-F AS-F Applicable tubing O.D. d TMH ASD AS L3 A L4 D1 AS-FE KE AS-FG L2 L1 M1 AS-FP H (Width across flats) T AS-FM Metric Size [mm] Model d T H
Example: OMRON Corporation XS2Z-12 4 1 Signal H CAN_H 4 Signal L CAN_L 5 Compatible with DeviceNet specification Micro Style connector.
L G ZA F H K J ZX I B C E D A ZR ZM 2 x M3 countersunk head screw mounting hole ZMA ZQ ZH ZU ZFC10, 20 ZL Applicable tubing O.D.
From the intersection G, trace the arrow mark to obtain the intersection H on the vertical axis. 9. The intersection H is the amount of water included in the compressed air 1 m3 at 0.7 MPa, pressure dew point of 25C. The amount of water is 3.0 g/m3. 10. Therefore, the amount of condensed water is as following.