Auto Switch Guide Use a 3-wire switch if this specification cannot be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Do not use a load that generates surge voltage.
P(MPa) 4. 1. :200(Kg) 2. :20(m/min) 3. :0.5(MPa) 4. :0.1 D 50 : : mmax 1 RS2H mmax : mmax (Kg) =0.1 =0.2 NO 50 400 280 mAm max 63 530 365 YES 80 800 565 V m mmax=0.1 200<400 mP6 -1-* -1-1V=20m/minm=278(Kg) 200278 NO mA m YES FA=mAg FA 2000.19.8 196(N) FAmAg(N) (g: :9.8m/S 2) P F -2-1P=0.5(MPaF=766(N)766(N) 196776 P7 -2-1 NO FA F RS2H50 YES v [m/min] m [kg] -1 5 - -
Nil Without auto switch (Built-in magnet) S 1 pc. 6 25 6 mm 25 mm For the applicable auto switch model, refer to the table below. n n pcs. 10 32 10 mm 32 mm 15 40 15 mm 40 mm Adjustment type 20 20 mm Nil With adjusting bolt B With shock absorbers (2 pcs.) Port thread type With shock absorber (With plate A) Installed on side A at time of shipment.
d i a n a p o l i s, I N ROCHESTER, NY (716) 321-1300 Vacuum Pad Series ZP Replacement Parts: Pad unit (With lock ring/Without lock ring) Pad Unit/How to Order Lock Ring Unit/How to Order ZPL 1 X19 U N 10 ZP Applicable pad dia.
When tightening the mounting screw, use a watchmakers screwdriver with a 5 to 6 mm handle diameter and tighten with a torque of 0.5 to 0.7 N m. (Refer to Figure 1.)
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
Module A Module consists of a wireless master or a wireless slave combined with I/O units and a valve manifold. Monitor mode Monitor mode allows the user to monitor the configuration of the wireless units but not make setting changes. N NFC Abbreviation of Near Field Communication.
Use a 3-wire switch if this specification cannot be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Do not use a load that generates surge voltage.
Therefore, check that ozone condensation is not more than a standard value of 0.1 ppm in the operating environment while the ionzier is in operation. m) Avoid using in a place where direct vibration or shock is applied to the main body. n) Avoid using in a place where there is a force large enough to deform this product or weight is applied to the product. 6.
Use a 3-wire switch if this specification cannot be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Do not use a load that generates surge voltage.
Use a 3-wire switch if this specification cannot be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Do not use a load that generates surge voltage.
A 2 to 200 L/min flow range option has been added. A rear ported type has been added. A flow adjustment valve (0.05 to 5 L/min) has been added.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire.
A model should be selected with a gripping force of 7 to 14 times that of the workpiece mass. If high acceleration, deceleration or impact forces are encountered during motion, a further margin of safety should be considered.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL W/LOCK, A/CUSH, A-SW, ACTUATOR, CNG CYLINDER W/LOCK, LE, 32MM CNG DBL ACTING, AUTO-SW, .00000 lb
14 A B A 14 A B A B A 14 A B A 14 A B 3 2 A 14 U side D side D side U side 0 1 5 4 2 3 B 12 B 12 B 12 B 12 B 12 7 8 1 2 3 4 5 Valve stations EX600-ED4 1 set EX600-WEN1 1 set EX600-EU1 1 set SS5Y3-10S6WE72-05B-C6 (Type 10 5-station manifold base, Wireless EtherNet/IP) Negative common, M12 connector IN/OUT pin arrangement 1, I/O unit: 2 stations * SY3100-5U1 3 sets (2-position single part
Minimum number of T nuts required for each stroke Stroke (mm) 100400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 Number of T nuts (pcs.) 8 10 12 14 16 18 20 Model LJ1-T8 (Weight: 8.4g) M8 x 1.25 17.5 7.5 15 The end cover must be removed when a T nut is inserted into the T slot. 18 11.5 M6 x 20 4 positions 45 10 T slots for mounting 9.4 4.5 T-slot size End cover A A A A 110 The A dimension
The tensile strength of the power cord is 49 N, and pulling it with a force greater than this can cause failure. Hold by the body when handling. 4. Turn the setting trimmer gently using a watchmakers screw driver. Turn the setting trimmer gently using a watchmakers screw driver. Do not turn beyond the stoppers located at both sides.
16 No.ZL3-OM00801-A 7.2 1 (/) ZL3/ZL6 ZL3-JSY3140-5LZ -a 1 3) 2) DC24V 1) 300mm 300mm * *0.150.18Nm 2) D: E: 1 1 1 1 3) 1 1 2 X12 ZL3/ZL6 SY100-30-4A-6 1 2) / 1) 2) 300 4 DC24V 6 600 10 1000 15 1500 20 2000 25 2500 30 3000 50 5000 ZL3/ZL6 SY100-30-A *x2 17 No.ZL3-OM00801-A ZL3/ZL6 ZS-39-5G ZL3-LW1-N-A 1 1) N NPN P PNP 2 ZL3/ZL6 ZL3-EJ1-H-A 1 2) 1) M 0.35 MPa