PSE200 Never use in an atmosphere of explosive gases. The switches do not have an explosion proof rating. Never use in the pressure of an explosive gas as this may cause a serious explosion. Maintenance Warning Mounting 1. Perform a periodical inspections for proper operation of the switch. Unexpected malfunctions may cause possible danger. 2.
N o t e 3 ) F.P. and S. kits are provided with an exhaust on one side, while C kits are with an exhaust on both sides. K I TE L E C T R I C A L E N T R YC A B L E L E N G T H Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 ! Main Office: (650) 588-9200 ! Outside Local Area: (800) 258-9200 !
progrom is an impoftant pafi rl tltis suppllchain s-vstem. The progrant identiJies product series and options that are cornmonly used in the local market.
In addition, it can relay output as an alarm contact output when an alarm is generated. Alarm Alarm code Alarm description Operation status Main reason AL0 Memory error Stop There is an abnormality with the memory data in the controller due to a high level of noise. AL1 Controller error Stop There is an abnormality with the data in the controller due to a high level of noise.
Accessories Sold Separately/ International Standard The assembly consists of an A and B bracket and 2 mounting screws.
The cushion effect (smooth start-up, soft stop) is not available an intermediate stop or return from an intermediate stop using an external stopper, etc. When using an intermediate stop with the above information taken into account, implement measures to prevent particulate generation and set the operating pressure to no more than 0.3MPa.
Endurance Test An ozonizer was used in a pneumatic circuit to prepare air to an ozone concentration of 1ppm. The test specimens (system components made from HNBR and NBR) were operated using this ozoneladen compressed air, and the endurance of each type of component/material was measured and compared.
Do not use compressed air that contains chemicals, synthetic oils that include organic solvents, salt, corrosive gases, etc., as it can cause damage or malfunction. 2) Install an air filter, if necessary. Install an air filter close to the valve on the upstream side. A filtration size of 5 m or smaller should be selected. 3) Install an aftercooler or air dryer, if necessary.
Multistage Ejector RoHS Only for the models with a valve or pressure switch The ZL1 with an AC voltage valve is not compliant.
If an abnormal condition occurs, turn off the power supply and stop the flow of compressed air. If an abnormal condition occurs, such as smoke, a foul smell, or noise, immediately turn OFF the power supply and stop the flow of compressed air because there is a possible risk of electric shocks or fire. 2. Do not place your hands or foreign objects inside the unit.
Other error An undefined error has occurred. Input/output size error Module size has been exceeded. Abnormal number of system input/ output points setting error The number of system input/output points has exceeded the set value for the system. Abnormal setting for the connected Wireless Remote An invalid channel for setting the number of registered Remotes has been used.
Other error An undefined error has occurred. Input/output size error Module size has been exceeded. Abnormal number of system input/ output points setting error The number of system input/output points has exceeded the set value for the system. Abnormal setting for the connected wireless slave An invalid channel for setting the number of registered slaves has been used.
Other error An undefined error has occurred. Input/output size error Module size has been exceeded. Abnormal number of system input/ output points setting error The number of system input/output points has exceeded the set value for the system. Abnormal setting for the connected wireless slave An invalid channel for setting the number of registered slaves has been used.
(Refer to 2.3.1 Contact input signal TypeFormatFormSetting) If an input from an external switch is detected, it can be generated as an alarm.Options to select continuous monitoring or monitoring during operation are available. Also, the detection start time after the start of operation and the detection end time can be set.
Therefore, if an air compressor has a low air delivery, the pressure may not be sufficient. Auto Drain Caution The auto drain may not function properly, depending on the quality of compressed air. Check its operation once a day.
Precautions Plug a connector in or out vertically, never at an angle. Applicable cable O.D.: 3.5 to 7 (Reference) 0.5 mm2 2 core and 3 core wires equivalent to JIS C 3306.
0 n r Ro 18 tio ta or tio ta t f n r Ro fla an le ge ng of si +10 0 0 Ro 19 tat or io t f n r fla an gle ge sin of With external stopper For 90 For 180 Single flat Single flat 5 A A e ng ng ng le le ra ad ad t ju ju en st st m m m st en en ju t r t r ad an an gle ge ge An 5 5 B port A port B port A port 90 A 5 ng ge le an ad t r ju en st m 180 Note) The drawings show the rotation range
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
Also, during an emergency stop or a power outage, no current will be applied to the valve, and the pressure in the cylinder will be sealed. Manual valve (Built-in base) When an emergency stop is input or a power outage lasting longer than 5 minutes occurs, the set data will be erased.