Note 2) Bore sizes ø80 and ø100 do not have trunnion holes.
If you do not want to use brackets, you can select either option.
However, if a trunnion bracket may be used later, select symbol “Z” (with trunnion mounting female thread).
Note 1) Do not disassemble the shaft trunnion type because assembly accuracy is required.
Note 2) MB series seal kits come with a grease pack.
③ Do not position the port facing vertically downward.
④ Keep the piping as short as possible with minimal bending.
Note 1) When used as a single-side hydro unit, air may be mixed in with the operating oil. Consider periodic checks and air bleeding or changing to use as a double-side hydro unit.
No, we do not offer any explosion-proof auto switches.
However, depending on the contact signal converter (commonly known as a barrier relay), which are sold by various manufacturers of electrical control equipment, an SMC auto switch may be usable in combination.
Reed auto switches do not respond due to the magnetic force of the magnet. While reed auto switches may respond to some models, the response is too unreliable for use. Therefore, an air gripper with a larger hysteresis than a solid state auto switch and a shorter piston stroke cannot be used with a reed auto switch for reliable detection.
Note 1) Do not adjust to ±5° or more at the rotation end. This may interfere with the operation of the product.
Note 2) Even if the rotation angle is adjusted to ±5°, adjustment of the auto switch for detecting rotation is not necessary.
If you do not plan to configure the emergency stop circuitry as described above, you can use the same power supply for the control power supply (C 24 V) and the motor power supply (M 24 V).
When moving by hand, do not connect the actuator cable to the controller’s CN2 (motor connector).
Use an AREA signal to do this. The AREA signal turns ON when the current position is within the AREA1 to AREA2 range.
AREA1 and AREA2 can be set for each step.
This conversion cable is a dedicated cable; do not use other commercially available products.
Note 1) Controller setting kit: A conversion cable (P5062-5) is not required for the JXC-W2.
Note 2) Controller setting kit: A conversion cable (P5062-5) is required for the LEC-W2. The JXC91/JXCD1/JXCE1/JXCP1 series catalogs can be found
https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=electric-actuators&fa_id=10838
(After discharge, do not forget to return the drain cock to its original position by tightening it clockwise.)
With auto drain: Normally, drain discharge is performed automatically when drain accumulates, so no action is required.
However, drain can be discharged by manual operation if needed.
Devices after the AM series filter do not actively remove water. The foreign matter which adheres to the element and then accumulates at the bottom of the case can be removed by draining it, but what can be removed is the oil mist or fine solid particles that weren’t caught by the main line filter.
As steam is a gas, it cannot be removed by filtering.
Note) Do not apply pressure higher than the max. display pressure to the pressure gauge during pressure adjustment; otherwise, the pressure gauge may be damaged.
ITV1000 series regulators do not use grease on the parts in contact with fluid.
ITV2000 and ITV3000 series regulators structurally require the use of grease, and therefore cannot be oil-free.
There are some special order products (for the painting industry) in which the grease has been changed to white Vaseline.
For details, contact your local SMC sales office.
When ordered with an “AC□□□” part number, brackets do not need to be ordered separately because the combination comes connected with a spacer with a bracket.
Note) Do not apply pressure higher than the max. display pressure to the pressure gauge during pressure adjustment; otherwise, the pressure gauge may be damaged.
Do not rotate it any further than this. Adjust the oil dripping amount as air is flowed. Note that the numbered scale markings are guidelines for adjusting the position and not indicators of the dripping amount.
Note) The AL10-A is adjusted by opening the needle at the front of the product.
Do not use the spacer (with a bracket) of the AC series unit for high-pressure specification (special order part number suffix “-X425”) products.
When assembling high-pressure special order products, AF20 to 60-*-A-X425 and AR20 to 60-*-B-X425, prepare a nipple for installation.
As fine oil particles of 2 μm or less do not easily adhere to the inner walls of piping, the AL430 is ideal for supplying oil mist to downstream equipment or for when you want to branch the piping on the outlet side.
The main target objects of such lubrication are bearings, chains, cutting machines, presses, etc.
The AL40 is a full-weight lubricator.