MWP_E MWP*-OM0020Q-B PRODUCT NAME Air Press Cylinder MODEL/ Series/ Product Number MWP Series Contents Safety instructions 2,3 ActuatorsPrecautions 48 Air Press Cylinder Specifications Specifications 9 Operation Principle 10 Relationship between the output and stroke 10 Installation and Handling Mounting Orientation / Installation 11 Application Examples 11 Cylinder Replacement 12 References 12,13
Fig. 11 Removal of rod seal and cushion seal Squeeze the seal from the external circumference to lift one part of the seal, and remove it. Fig 12 How to remove piston seal 3) Tube gasket Take out with the precision screwdriver. 26 - 4-4-3. Grease C a u t i o n Use a specified grease.
Also, if pipe tape is used, as in Fig. (11), leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating air Air supplied to the rotary actuator shall be cleaned by the filter. CRA1 series is lubrication free.
22 1 12 2 13 3 14 4 15 5 16 NBR 6 17 7 18 8 A 19 9 B 20 10 21 11 22 -15- 1 14 2 15 3 16 4 17 5 18 6 19 NBR 7 20 8 21 9 A 22 10 23 11 24 12 25 13 -16- 3. 3.1. 1 I/O LEC-CN5-* / PLC 1 2 DC24V CN5 1 LE-C*-*-* LE-C*-*S-* CN4 CN3 CN2 120.3 120.3 mm mm 200 200 mm/s mm/s 2 100 500 100 500 1 1 200 1000 200 1000 2 2 50 200 50 200
If a product different from the one ordered is installed, injury or damage can result. -11- 2.5 Operating Environment Warning 1.
(Page 11) 7 1000 fR[N] 100 Lateral load applied to rod 100 80 63 10 50 40 1 0 500 1000 1500 Cylinder stroke [mm] Fig 1. Allowable lateral load applied to rod end C a u t i o n Be certain to align the rod axis with the load and direction of movement when connecting.
Coil 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Terminal no.2 (-) Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm. Note 3) Round or Y-shaped crimped terminal cannot be used.
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (such as the installation of a cover or the restricting of access to the product) to prevent potential danger caused by actuator operation. 11. Do not disassemble the product or make any modifications, including additional machining.
(The first digit of the lower level will start PV flashing.) 11. Press key change 20 to 30. SV 12. Press SEL key to set the value. 13. Press key to return to PV/SV display. SV 313 IDH Series 3.10 Functions and operation of temperature controller IDX-OM-W037 Thermo-dryer 4.
(See Fig.13) Replacement part: Shock absorber Bore size Part no. 32 RB1007-X225 4050 RB1407-X552 Lever Hexagon socket head set screw Push down Fig. 11 10 - Lever Shock absorber 11.Internal construction 12 16 Push down Replacement Grease applied Approx.5mm Fig. 12 Fig.13 20 11 - 32&50 Component Parts (12&50) 12 - Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81
Replace the product in the case of failure such as difficulty removing or inserting tubing. 11 - 5. Construction Male connector Male elbow No.
Maintenance 11 9. Mounting accessories (option) 12 10.
-segments, 7-segments for other) Number of display digits Sub display (right): 5 digits (partially 11-segments, 7-segments for other) Operation light LED is ON when switch output is ON (OUT1, OUT2: Orange) Digital filter 5 Variable from 0 to 30 s/0.01 s increments -79No.PS-OMW0005-C Product No.
(Refer to page 11) Please order separately. -22No.PS-OMM0007-I Pressure Setting Measurement mode The measurement mode is the condition where the pressure is detected and displayed, and the switch function is operating. This is the basic mode, and other modes should be selected for setting changes and other function settings.
This matches the controller. (2) Check Parallel I/O configuration matches (NPN or PNP). (1) LEL25LT-300 NPN (2) -11- 2.3 Construction 11 8 Motor option with motor cover Motor option with lock 24 3 6 2 4 1 14 22 12 17 13 17 7 B A-A(LEL25LT-) A-A(LEL25MT-) B 19 19 23 5 21 20 16 9 10 15 18 No.
(Refer to page 11.) 1) If a lubricant is used in the system, use class 1 turbine oil (no additive), ISO VG32.
Since cylinders receive excessive force in such a case, do not design circuit synchronizing cylinders only. 11. Mounting Methods Various mounting methods are available as follows. Bottom mounting Side mounting 11-1. Cautions on Mounting 1) Never place your hands or fingers between the plate and the body.
Auto switches When an auto switch is mounted or its set position is changed, refer to pages 11 to 17. Caution Use a specific mounting bracket (Table 3 on page 12.) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque.
Installation and Wiring . 11 3-1 Installation . 11 3-1-1. Precautions for Installation . 11 3-1-2. Installation of Ionizer . 12 3-2. Wiring . 13 3-2-1. Connection Circuit . 13 3-2-2. Wiring of the Power Supply Cable . 15 3-2-3. Wiring of the AC Adapter . 15 3-3. Timingchart . 16 4. Function . 17 4-1. Name of Parts. 17 4-2. Adjustment of Offset Voltage . 17 4-3.
0.13 the values in the table 11. 20 0.24 Piston speed has to be less than the allowable value 25 0.45 32 0.88 40 1.53 23/28 6.