TUH Series Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators. 3. Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1.
As a rough guide, thighten the screw an additional 90o after feeling a tight resistance. Switch reset position(OFF) MHZ2 MHZJ2 Protrusion of Auto Switch from Edge of Body MHQ The maximum protrusion of an auto switch (when fingers are fully open) from the edge of the body is shown in the table below. Use the table as a guideline for mounting.
Verify the specifications before use. -100 to 0 kPa Setting pressure range -0.1 to 0.45 MPa -0.1 to 0.4 MPa 0.4 (0) MPa (kPa) Air/Non-corrosive non-flammable gas Applicable fluid 0.2 (-50) Setting Pressure Indication light Switch ON: red LED turns on 0 (-100) -0.1 t Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Pull a new element by the cloth handle toward the center, and put it inside the basket, folding the edge of an element. Further, push the edge of an element to the basket s bottom-plate flange surface thoroughly. Tightening bolt Stopper Basket Edge of the element 1-4. Remove the cover upward by turning it counterclockwise.
arm length of 100 mm and an operating pressure of 44 psi [0.3 MPa], according to the graph, the maximum clamping force is 45 lbf [200 N].
This product generates high voltage, so it can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of systems should be performed by trained and experienced operators. 3.
Due to meter-in control, the cylinder moves from A to B regardless of whether it is an initial operation or a normal operation. When it reaches B, the head pressure (PH) rises quickly as indicated by the line from C to D.
Lube Related Products: Strainer At the terminal of an air pressure line in which a D.P. Lube is used, install a strainer (filtration rate of 5 m) upstream with a metal seal solenoid valve, which is susceptible to dust. Float switch mounting position Mounting orientation is upward.
Absolutely never use in an atmosphere where explosive liquid or gases are used. Unit does not have explosion-proof construction. If used in an atmosphere of explosive gases, there is a possibility of causing an explosion. D2 Blue () COM 14-11-18 3 Digital Pressure Sensor Series GS40 Dimensions 14 10 F.R.L.
Note 3) Impact resistance: No malfunction resulted during an impact test using a drop impact tester. The test was performed one time each in the axial and right angle directions of the main valve and armature for both energized and de-energized conditions. Vibration resistance: No malfunction resulted during an one-sweep test between 8.3 and 2000Hz.
For information on tubing connection, refer to the pamphlets High Purity Fluoropolymer Fittings Hyper Fitting Series LQ1/2 Work Procedure Instructions (M-E05-1) or Flare Type Series LQ3 Fitting Procedure (M-E06-4). (The pamphlets can be downloaded from the SMC website.) Caution 1.
Absolutely never use in an atmosphere where explosive liquid or gases are used. Unit does not have explosion-proof construction. If used in an atmosphere of explosive gases, there is a possibility of causing an explosion. D2 Blue () COM 14-11-18 Digital Pressure Sensor Series GS40 Dimensions 14 10 F.R.L.
Absolutely never use in an atmosphere where explosive liquid or gases are used. Unit does not have explosion-proof construction. If used in an atmosphere of explosive gases, there is a possibility of causing an explosion. D2 Blue () COM 14-11-18 3 Digital Pressure Sensor Series GS40 Dimensions 14 10 F.R.L.
Lube Related Products: Strainer At the terminal of an air pressure line in which a D.P. Lube is used, install a strainer (filtration rate of 5 m) upstream with a metal seal solenoid valve, which is susceptible to dust. Float switch mounting position Mounting orientation is upward.
Safety Instructions Be sure to read Handling Precautions for SMC Products (M-E03-3) before using.
HANDLE LOCK NUT SETTING SPRING RELIEF VALVE EXH&BLEED PILOT VALVE DIAPHRAGM SUP OUT ELEMENT DRAIN COCK DRAIN SUP 1 Setting Main Composite Displacement Pressure MPa +/-Force Displacement OUT Spring Valve spring m m N/m MPa/m m/N Diaphragm Force N m2 Block Diagram -5- 3.
Y7NWV IC circuit 5 V 12 V Diagnosis (2-color indication) Y7PW Y7PWV Y7BW Y7BWV 2-wire 12 V Water resistant (2-color indication) Y7BA Lead wire length symbols: 0.5 m Nil (Example) Y59A 3 m L (Example) Y59AL 5 m Z (Example) Y59AZ Refer to page 12-13-25 for solid state switch with pre-wire connector.
High Filtration (0.3 m) Space-saving and easy piping. (For further information, Refer to Best Pneumatics Vol. 16.)
Symbol Nominal filtration accuracy (m) Note) Stainless steel 304/Epoxy Stainless steel 316 Polyester/PP Nominal filtration accuracy (m) 0.5 1 2 5 10 20 40 50 70 74 75 100 105 120 X50 001 002 005 010 020 040 050 070 074 075 100 105 120 FGDT, F FGDC, E Note 1) The industrial filter described in this catalog are products in which an element is incorporated into a vessel.
If the power should not come back on, please contact P/A for an inspection.