ECC-PNAL-232CAB RS232C CABLE Do not pull on the cord.Have the case when remove the ECC-PNAL-232CAB cable. This cable might break when the code part of this cable is pulled when this cable is removed. Install the cover or the memory cassette after removing the ECC-PNAL-232CAB cable. Turn off the power supply when you install or detach the ECC-PNAL-232CAB cable.
Do not use a lubricator on the inlet side because it could clog the bleed holes and lead to a malfunction. 14-4-60 1 Regulator for 2 MPa Series ARX20 F.R.L.
Do NOT pipe upwards. AU200/300 Effective thread depth 6.5 4-M5 x 0.8 AU200, 300 Float type auto-drain Port size H G F E D C B A Model Port size 1 4 / 3 8 AU200 / 50 70 61 30 40.5 31.5 164 165 AU300 50 70 61 30 40.5 31.5 188.5 165 14-3-12
The silencer's response properties do not change in the initial stage, but will change due to the blockage after long use. Replace it after using about 500,000 times. This number is subject to change based on fluid quality and energization time. 2. When using a silencer, make space for silencer replacement. 1.The controller starts its output the moment the power switch is turned ON.
SlA w Note that in case of the option of different "1(P)" porting position, porting indication on the body and flow direction by handle operation are reversed. e Do not supply air pressure from other ports than 1(P) port. The valve may have air leakage when air pressure is supplied from other ports.
Note) Do not use excessive force to remove the connector as this might loosen the wire connections inside the connector. Open the cover by inserting a small flat head screw driver into the slot on the side of the pilot assembly(see drawing below), lift the cover out about 1 mm and then pull off.
Do not use it in a line that is kept pressurized because it could cause the body to break. 13-10-2 3 Air Suction Filter Series ZFA 100 200 Dimensions: ZFA Single unit Bracket ZX ZR Cover opened-up dimensions 70 Element extracted dimensions 55 ZM ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800)
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
(Do not cut the tube with plier6, nippers, scissors, utilitv knife, etc.) ePull out the tube while keeping the release button depressed. lJf the release butlon is nol held down, the tube cannot be withdrawn.) OGrasp the tube, then slowly push it until il comes lo a dead-end.
Lubrication aTh yah,e h8 bon lub,ric.td ior ltb d nrlnubcfrirE. and dor noa lqoirr fudfiar fubdcdion in svba. ef a lubricant is used in the system, use turbine oil type #1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate, as the original lubricant applied during manuiacturing will have been washed away. See table of suggested lubricants.
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?