IP8001 Series E With feedback lever unit for stroke 35 to 100mm. ExIP8001-010-EW F With feedback lever unit for stroke 50 to 140mm. 2: When 52ATEX type specify symbol M, 2, 5, blue cable grant is equipped for electric connection. W With body cover window.
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 2 - E/P Regulator Safety Instructions Caution 1. The product is provided for use in manufacturing industries.
Heat exchanger Ventilation Circulating fluid Expansion E circuit valve A Expansion Inverter pump valve B Pump E Temp. sensor (Ref. discharge Ball tap Fluid level gauge TS Press. sensor Over flow port (Ref. low press.)
In such cases, human injury may occur; e. g., by 3 8.
. -8No.D-S-OMG0006-C Model Indication and How to Order Sensor unit : One sensor connector (e-con) is included in each package. : One sensor connector (e-con) is included in each package. Amplifier unit Accessories (Option) Product number Contents Remarks ZS-28-C-1 Sensor Connector (e-con) 1 pc. D-MS-A Mounting screw (M2.5 x 4 L, Steel (Black zinc chromate)) 1 pc.
Please refer below for calculation of kinetic energy. 2 I 2 1 E E : Kinetic energy J I: Inertia moment kg/m2 : Angular speed rad/s Allowable kinetic energy for the rotary actuator is limited. The limit of rotation time is obtained by calculating inertia moment. Please refer following for obtaining inertia moment.
The end angular speed is obtained by: Table 7 Allowable kinetic energy (J) t Size Allowable kinetic energy : Rotation angle [ rad ] : Rotation time [ s ] 10 0.00025 15 0.00039 Kinetic energy E is obtained by: 20 0.025 30 0.048 40 0.081 E Therefore, the rotary actuator rotation time is: E: Allowable kinetic energy [ J ] : Rotation range [ rad ] I: Moment of inertia [ kgm2 ] Note) If the
E1 2 I E[J]I[kg][rad/s] Imr m[kg] rm 5.1 19 I I I I kg kg kg kg m m m m 2 2 2 2 m: m: m: m: kg kg kg kg b 20 5-2. 5.1 5.1 32 0.023[J] 40 0.028[J] 2 t [rad]t[s] E E1 2 I t E 2 I t E[J][rad]I[kg] 2 t (1) t = & (2) C C t 2 1 tdt 2 + = = & & t=0 =0C=0 t 2 1 t 2 1 2 = = & t 2 = 21 5-3.
Note 1) To change the port size of the 1(P), 3/5(E) ports into the Fitting Replacement By replacing a valves fitting assembly, it is possible to change the port size of the 4(A), 2(B), 1(P), and 3/5(E) ports. When replacing it, pull out the fitting assembly after removing the clip with a flat blade screw driver, etc.
Command error Response Block # 0 0 E E [CR] Unit No. Command Error Check sum code code When there is an error in the command block that has been sent, the response block above is sent back to the host computer side. Error code is a text data of 2 byte.
Vertical line of belt teeth Flaw which is made when the belt runs on the flange. e . Rubber back of the belt is softened and sticky f . Crack on the back of the belt 7. Troubleshooting 7.1 Alarms and Warning When a fault occurs during the operation, the corresponding alarm or warning is displayed.
D rai n w hi l e l i qui d l evel i s vi si bl e. D rai n pi pi ng: 5 m or l ess* N . C. aut o drai n: 4 or m ore ( I . D . ) , 10 ( O . D . ) N . O . aut o drai n : 6. 5 or m ore ( I . D . ) , 10 ( O . D . ) *AM 850: 9 or m ore ( I .
Usable stroke by buckling strength Usablestroke by Mounting style Pressur buckling strength (cm) e Symbol and sketch Symbol 125 140 160 180 200 250 320 (MPa) of bracket Rod side 0.3 103 92 113 108 124 155 162 Head L Foot: side Frang flange e F 0.5 79 70 86 81 94 118 122 L G F 0.7 66 58 72 67 78 98 101 0.3 45 38 47 46 54 67 69 0.5 33 27 34 33 39 49 49 G 0.7 26 22 27 26 31 39 39 0.3 96 83
Check the product for the following points before operation. a) Damage to power supply line and signal line. b) Looseness of the connector to each power line and signal line. c) Looseness of the actuator /cylinder and controller /driver mounting. d) Abnormal operation. e) Emergency stop of the total system. 3.
E: Contents are added. F: Contents are added. G: Contents revised in several places. H: Contents are added. I: Contents revised in several places.[March 2017] J: Contents revised in several places.
Allowable kinetic energy (J) t Model Allowable kinetic energy (mJ) : Rotation angle [ rad ] : Rotation time [ s ] Basic type CRJB05 0.25 Kinetic energy E is obtained by: With external stopper CRJU05 1.0 Basic type CRJB1 0.40 Basic type CRJU1 2.0 E Therefore, the rotary table rotation time is: E: Allowable kinetic energy [ J ] : Rotation range [ rad ] I: Moment of inertia [ kgm2 ] During
12 Red 12 E 2 phase stepper motor PD Yellow 11 F 8 5 phase stepper motor For a signal power supply of 24VDC, connect an external resistor R (1.3k 1/2W) in order to hold the current to 15mA or lower.
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Body Valve Valve seat Collar Spacer Lock ring Sleeve Chuck Valve O-ring Valve seat O-ring Plug O-ring Valve spring Sleeve spring Cassette Seal Stem Cassette Seal Brass PBT PBT PBT PBT PBT Cold rolled carbon steel sheet Stainless steel FPM NBR NBR Stainless steel Stainless steel NBR Brass NBR Electroless nickel plated Electroless nickel plated 4 S e
If the guide rod is twisted or bent, its operating resistance will become very high, causing its bearings to wear prematurely and its performance to be lowered. e Install the cylinder in an area in which it can be serviced easily.
Material Replacement Parts Material Note Component Parts VQZ No. q w e r t y No. !0 !