Intrinsically Safe Valve Equipment Uo (or Voc) lo (or Isc) Po Co (or Ca) Lo (La) Ui li Pi Ci + Ccable Li + Lcable If the cable capacitance and inductance are unknown, use the following values: Ccable = 60 pF/ft., Lcable = 0.2 H/ft.
Pressure Regulator for General Applications Series BP1000 Operating pressure: 0.5 to 300 psig (0.0034 to 2.1 MPa) Body material: Stainless steel and Brass available Hastelloy internals available for corrosion resistance How to Order Port Number q w e r BP10 01 4PL 4 4 S 0 0 Operating pressure Bonnet option Code pressure 0.5 to 10 psig (0.0034 to 0.07 MPa) 1 to 30 psig (0.007 to 0.2 MPa) 2 to 60
Wiring of power source for driving counter For power source for driving counter, use the one with 90 to 264 VAC, 50/60 Hz or 21.6 to 26.4 VDC, 0.4 A or more. 3. Output circuit There are two outputs, the NPN open collector and the PNP open collector. The maximum rating is 30 VDC, 50 mA. Operating the controller by exceeding this voltage and amperage could damage the electric circuit.
CE2 IN 84.8 59 42 25 CQSY16-PS 12 6 OUT 113 79 57 34 CQSY20-PS ML2B IN 151 106 75 45 CQSY25-PS 16 8 OUT 201 141 101 60 When only grease for maintenance is necessary, please order by the following part numbers.
The angle is 60 when any of the following auto switches are used: D-90/90A/97/93A The angle is 69 when any of the following auto switches are used: D-S99(V)/T99(V)/S9P(V) 3.
Note 3) As a guide, the load mass should be approximately 60% of the thrust load factor. 32 40 Note 1) Exceeding the allowable pressure will lead to the breaking of the magnetic coupling and cause the piston slider and external slider becoming separated.
Add 10 g for conduit, 30 g for DIN terminal, and 60 g for conduit terminal type respectively. Note 3) Refer to Glossary of Terms on page 226 for details on the maximum operating pressure differential and the maximum system pressure.
Note 3) The symbol F in the dimensions indicates the position where the clamping force is generated defined by the product specifications. 82 WRF100 Dimensions WRF-S/S-type clamp arms (Without cover) WRF100-S200/S240 4 x M8 x 1.25 depth 12 108 60 2 x M12 x 1.75 through 25 25 80 0.015 0 2 x 8H7 ( ) 60 0.05 depth 12 (2 x 4 x M5 x 0.8 through) ( ) C B For limit switch mounting A 60 60 36 0.5
Note 3) Refer to page 60 about the SUP/EXH block disk assembly and method of handling of parts at different pressure. 77 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Install this product after discharging the drainage that has already accumulated in Mounting Example Compressor Aftercooler Air tank Main line filter Air dryer How to Order ADM200 Port size OUT IN Symbol 04 03 3 8 3 8 Construction/Dimensions 1 2 3 8 Voltage 100 VAC Hz 1 50 60 200 VAC Hz 50 60 240 VAC Hz 50 60 110 VAC Hz 50 60 220 VAC Hz 50 60 24 VDC 12 VDC 2 3 4 5 6 7 Set screw Operating
The intersection E is the dew point under pressure 0.7 MPa with the ambient temperature of 30C and the relative humidity of 60%. Value for E is at 62C. 5. Trace the intersection E upward, and C leftward to obtain the intersection D. 6. The intersection C is the amount of water included in the compressed air 1 m3 at 0.7 MPa with the pressure dew point of 62C.
CE2 IN 84.8 59 42 25 CQSY16-PS 12 6 OUT 113 79 57 34 CQSY20-PS ML2B IN 151 106 75 45 CQSY25-PS 16 8 OUT 201 141 101 60 When only grease for maintenance is necessary, please order by the following part numbers.
YB-03 32, 40 80 9 6.5 10 18 50 d2 d1 YB-05 50, 63 120 11 6.5 12 22 60 L UT C UA (mm) Part No.
Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) The analogue input update time is set for every wireless slave unit. Analogue input update time Define the address assignment direction of the EX600 I/O units connected to the wireless master unit. The address assignment direction is changed by mode 1/mode 2. Be careful about the I/O map.
Setting range: 0.1/0.2/0.5/1/2/5/10/30/60 s (Initial value 1 s) The analogue input update time is set for every wireless slave unit. Analogue input update time Define the address assignment direction of the EX600 I/O units connected to the wireless master unit. The address assignment direction is changed by mode 1/mode 2. Be careful about the I/O map.
[F90] Setting of all functions completed : Setting of each function Every time the SET button is pressed, the display moves to the next function in order of "Setting of each function" on page 60. Set by using the UP and DOWN buttons.
(increment of 1 sec.), 20 sec., 30 sec., 40 sec., 50 sec. and 60 sec.
The slant angle of each rope should be 60 degrees or less. Never lay the product on its side. The compressor oil will leak in to the refrigerant piping, which may cause early failure of the compressor. Drain the residual fluid from the piping as much as possible to prevent any spillage.
Thermostat working temp. : 60+/-5 C (at radiating water side) Thermostat ERR14 Alarm 90+/-5 C (at recirculating fluid side) After alarm occurrence : The unit (temp. control, pump) stop.
. -3No.LEY*-OMZ0010 1Rod type / LEY Series 1.1 Specification Model LEY 25E-X8 LEY 32E-X8 LEY 40E-X8 (3000 [mm/s2]) 20 40 60 30 45 60 50 60 80 Horizontal Work load [kg] Note1) (2000 [mm/s2]) 30 55 70 40 60 80 60 70 90 Vertical (3000 [mm/s2]) 7 15 29 10 21 42 12 26 52 Pushing force [N] Note2) Note 3) Note 4) 63 to 122 126 to 238 232 to 452 80 to 189 156 to 370 296 to 707 132 to 283 266 to 553