SY3000/5000/7000 Series Plug-in Type In addition, it is possible to shorten the energized time by making a valve with an N.O. (normally open) specification. 4. Effect of back pressure when using a manifold. Use caution when valves are used on a manifold, because an actuator may malfunction due to back-pressure.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 3 No.JXC-OMW1019-A LECP6 Series / Controller 1.
Outside of clean room Duct piping Series 11-/13-/22(Vacuum suction type) With a vacuum pump When several air cylinders are used together or a model with high vacuum suction flow is used. With an ejector When a few air cylinders are locally used.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, RND BODY, D/CLVS, D/ACT, ACTUATOR, CJ2 ROUND BODY CYLINDER, GE, 16MM CJ2 DBL-ACT AUTO-SW, .49468 lb
Never use them in the presence of an explosive gas, as this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized. (Please consult with SMC regarding the availability of a magnetic field resistant auto switch.) 3.
Doing so may cause human injury and/or an accident. 4. Effects of back pressure when using a manifold Use caution when valves are used on a manifold, because an actuator may malfunction due to back-pressure.
In such a case, it is necessary to use the digital pressure switch ZSE10 or ZSE30A with a fine smallest settable increment or a flow switch for flow rate detection. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
If the cylinder is used with an excessive kinetic energy, install an external absorber to prevent impact from acting on the cylinder body. If these countermeasures are taken, confirm the rigidity of the equipment carefully. C a u t i o n When a rubber cushion is used, there will be a slight bounce at the stroke end.
If the cylinder is used with an excessive kinetic energy, install an external absorber to prevent impact from acting on the cylinder body. If these countermeasures are taken, confirm the rigidity of the equipment carefully. C a u t i o n When a rubber cushion is used, there will be a slight bounce at the stroke end.
Maintain a minimum cylinder separation of 40mm. 3. Pay attention to the length of time that a switch is ON at an intermediate stroke position.
Especially when using a 3-position exhaust center valve, a double check valve, or a single acting cylinder, take appropriate measures to prevent malfunction by using it with an individual EXH spacer assembly or a back pressure check valve. 13. Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14.
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment such as valves.
Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salt or corrosive gases, etc,as it can cause damage or malfunction. 4 C a u t i o n Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller.
Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salt or corrosive gases, etc,as it can cause damage or malfunction. 4 C a u t i o n Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller.
View A-A (Internal connection diagram) Conduit When used as an IP65 equivalent, use seal to install the wiring conduit. Also, use the tightening torque below for the conduit.
If an instantaneous flow of 100 L/min lasts for 5 minutes, the accumulated flow will be 5 x 100 = 500 L. Accumulated flow Accumulated flow external reset A function to reset the accumulated value to "0" when an external input signal is applied. A type of output where a pulse is generated every time a predefined accumulated flow passes.
Do not If using the product in an interlocking circuit Provide a double interlocking system, for example a mechanical system. Check the product for proper operation. Otherwise malfunction can result, causing an accident.
Please contact SMC if it is necessary to hold a stopped position for an extended period of time. 4. Effect of back pressure when using a manifold. Use caution when valves are used on a manifold, because an actuator may malfunction due to back-pressure.
When combining a double check valve and an interface regulator, use a manifold or sub-plate as a basis, and stack them in the following order; the perfect spacer the interface regulator the valve.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 2. When there is a large amount of drainage Compressed air containing a large amount of drainage can cause the malfunction of pneumatic equipment.