SMC Corporation of America
Elite Part Number Search
Search Results "CDLA2D100TN-350-E-M9PSDPC"

2 E 1 0 E E _ E 5 E E c r l 0 1 2 3 4 5 6 7 I I 101112131415 Distance from cylinder axis: Lo (cm) Example The required load, Fo =100(N) and the moment arm, L0 = Bcm refering to Data 1, draw a vertical line from the 8cm value of the horizontal axis.

R 22.5 1 E 125 At accessory E: 110 At accessory F: 110 { } 5 150 194 125 G1/2 Electric conduit 35 At accessory E: 195 At accessory F: 275 { } 4 x M8 x 1.25 depth12 (Female thread for rear mounting) With optional resin cable clamp Applicable cable O.

Without brake C section Brake electric circuit YellowC;*1 Y e l l o w O Y !

W M L H E W M 10 14 18 22 30 36 14 20 25 29 37 49 46.5 57 79 88 103 122 11 16 21 24 32 41 10 17 22.5 24.5 27 30 1/8" 1/4" 3/8" 1/2" 3/4" 1" LQ3U1A LQ3U2A LQ3U3A LQ3U4A LQ3U5A LQ3U6A 1/4 (E) (E) L

L E E E E L S L L L S S S S L L L L L 6 9 6 9 6 9 6 9 6 9 IN IN IN MPa MPa MPa MPa MPa Right Left Right Bracket DIN rail mounting bracket DIN rail mounting bracket Stations 1 Stations 1 Stations 1 2 3 IISA2NSR-1B1 set (1 station manifold part number) ISA2-GE41P1 set (Air catch sensor part number) IISA2NSR-3D1 set (3 stations manifold part number) ISA2-HE41P 3 sets (Air catch sensor part number

y U side e SUP block disk assembly (Release pressure side) EXH block disk assembly (Vacuum pressure side) w e q r D side Component Parts / Plug-in Note Part no.

F: Angle adjustment range 5 E: Angle adjustment range 5 E: Angle adjustment range 5 B port Angle adjustment screw A port Clockwise rotation 0 8 0 e Allowable Lateral Load to the Piston Rod End gl 10 n a e nt gl e an m st t en u dj m a m st u ju m i in ad M Using friction fittings makes it easier to mount the load to the piston rod end.

-2No.PS-OMG0005CN-E / 1 1.5 *3) *3) 1 1 [] -3No.PS-OMG0005CN-E () () () () -4No.PS-OMG0005CN-E () * UL UL1310 2 UL1585 2 30[Vrms] 42.4[V ]2 UL SUS316L , (ZS-31-X175X186X188X189) () NG NG -5No.PS-OMG0005CN-E * (Nm) RNPTRc1/8 79 RNPT1/4 1214 TSJ Crawford fitting (Swagelock )URJ Cajon (VCR ) FG (50N () () 6 33 ( ) () -6No.PS-OMG0005CN-E 30m DC(-)() () * ( ) () CE -1060 *

Since the PTFE seal is used for element e, a certain amount of force is needed to set the element. Set the element in the following procedure. Handle element e carefully to keep it clean, for example, open the element package only when the element is mounted. a. Fit the grooved part of gasket w into the flange part of case q. b. Place element e in case q.

Component Parts No. q w e r t y No. u i o !0 !

= 0.2 () = 0.018 2 1000 V = 1.4 x 300 = 420 1 420 2 E = 0.2 () = 0.018 2 1000 V = 1.4 x 300 = 420 1 V 2 E = W () 2 1000 1 V 2 E = W () 2 1000 Find the kinetic energy E (J) of the load.

Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.

the mode SW (Close the cover after changing SW) u i e Cover o !

Lights up when it is turned ON. kgf/cm2 bar PSI inHg mmHg OUT1 OUT2 CH Channel display 1 2 3 4 P R E S S U R E Displays the selected channel. UP button Use this button to change the mode or set value. SET DOWN button SET button Use this button to change the mode or set value. ZSE ISE Use this button to set the mode or set value.

Fuel oil (up to 60C) Fuel oil (up to 100C) B PTFE EPDM Brass or BC6, Copper J A H A H A H D N Note 2) FKM EPDM FKM NBR FKM EPDM PTFE FKM FKM EPDM PTFE(FKM) PTFE(FKM) NBR H Note 1) Steam system (Steam) S Q B Steam system (Boiler water) Steam system (Condensate) Insulation oil Naphtha Parachloroetylene Brake oil Water (up to 99C) G, J E P A H A H A H B J D, E N, P If using for other fluids

RY(n+2).E RX(n+3).F RY(n+2).F n: Start address -42No.EX-OMW1003-A Bit area (3) Input register Slave -> Master Output register Master -> Slave Corresponding Unit No.

Since the PTFE seal is used for element e, a certain amount of force is needed to set the element. Set the element in the following procedure. Handle element e carefully to keep it clean, for example, open the element package only when the element is mounted. a. Fit the grooved part of gasket w into the flange part of case q. b. Place element e in case q.

Key Position and Rotation Range Single vane type Double vane type 90 180 270 90 n o r a a ti r n n g n a o e g n o t ti r a ti o n a a 2 e g t r t o 7 e o 1 r y 0 r 9 8 y e 0 y +4 0 e 0 Key K e K +4 0 +4 0 K +4 0 Key Key 0 (45) 9 Key e Standard Optional g n a r n o ti a t o r (90) y e K (45) (45) A port B port A port A port A port B port B port B port 100 190 280 100 a r n n n r o a g