SMC Corporation of America
Elite Part Number Search
Search Results "ISE20-N-M5"

Tightening Torque for Piping Applicable Connection thread Proper tightening torque (N m) 1. Polarity When connecting power to a solenoid valve with a DC specification and equipped with a light or surge voltage suppressor, check for polarity. If there is polarity, take note of the following. No diode to protect polarity.

Warning Connection thread Proper tightening torque (N m) Rc1/8 7 to 9 Rc1/4 12 to 14 Follow the procedure of the manufacturer when fittings other than SMC is used. 6 VFR2000-OMH0002-A VFR2000 Series Precautions for 5 Port Solenoid Valve Be sure to read before handling. Air Supply Maintenance 1.

Take appropriate measures so that a force of 30 N or more is not applied to the lead wire. When instructions are given in the Specific Product Precautions, follow these specifications. Lubrication 1.

M5 types After tightening the fitting by hand, use a wrench to tighten the Please consult with SMC, as there are some standard valve products that use fluorine grease for food processing equipment (NSF H-1). fitting an additional approximately 1/6 to 1/4 turn.

Internal gripping force 6.1 Note 1) Gripping force per finger Effective value (N) O.D. External gripping force 1.9 S I.D. Internal gripping force 3.7 C Open/close stroke (Both sides(mm) 4 Note 2) Weight (g) 27 28 26 27 Note 1) Values based on pressure of 0.5 MPa, gripping point L=20 mm, at center of stroke. Note 2) Values excluding weight of auto switch. 4 - 2.

If it lacks rigidity, it could apply an unbalanced load on the cylinders, leading to a considerable reduction in the durability of the cylinders. 4.12-3 How to Select an Applicable Model IN OUT Data D Theoretical output table Bore (mm) Piston area (mm2) Rod size (mm) Operating direction Operating pressure (MPa) Unit: N 0.2 62.8 52.8 98.2 82.4 161 138 252 220 392 330 624 560 1010 908 1570

If it lacks rigidity, it could apply an unbalanced load on the cylinders, leading to a considerable reduction in the durability of the cylinders. 10-17-3 Model Selection IN OUT Data (D) Theoretical Output Bore size (mm) Piston area (mm2) Rod size (mm) Operating direction Operating pressure (MPa) (N) 0.2 62.8 52.8 98.2 82.4 161 138 252 220 392 330 624 560 1010 908 1570 1430 2460 2260 3080

Magnet: None, Mounting: B (Basic Style), Style: N (Non-lube Rubber Bumper), Bore Size: 100mm, Thread: TN (NPT Ports; M5 for Air Cushion 20 & 25 Bore), Seal Material: V (FKM), Stroke: 50mm, Auto Switch: None, Lead Wire or Prewired Connector: 0.5m (Or None in the Case of No Switch), Number: 2 pcs. (Or None in the Case of No Switch), X Option: X165US (Inch Rod Thread)

Magnet: D (Built-in Magnet), Mounting: T (Head Trunnion), Type: A (Air Cushion), Bore: 40mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 1200mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: N (Pivot Bracket not Assembled), Rod End Bracket: W (Double Knuckle Joint)

Magnet: D (Built-in Magnet), Mounting: B (Basic), Type: N (Rubber Bumper), Bore: 32mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 150mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: A93V--Reed, DC Volt, AC Volt, LED, Vertical

Magnet: D (Built-in), Mounting: B (Basic Style), Style: N (Non-lube Rubber Bumper), Bore Size: 40mm, Thread: Rc (M5 for Air Cushion 20 & 25 Bore), Seal Material: R (NBR), Stroke: 600mm, Auto Switch: G5BA--Solid State, Water Resist., 2 Wire, Lead Wire or Prewired Connector: MBPC (1.0m Cord Length, M8-4 Pin Connector)

Magnet: D (Built-in Magnet), Mounting: F (Rod Flange), Type: N (Rubber Bumper), Bore: 32mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 600mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9PA--Solid State, Water Resist., 3 Wire PNP, Horizontal, Lead Wire or Prewire Connection

Magnet: D (Built-in Magnet), Mounting: Z (Basic, w/o Trunnion Mounting, Female Thread), Type: N (Rubber Bumper), Bore: 32mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 600mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: No Switch, Lead Wire or Prewire Connection: 0.5m (Or

Magnet: D (Built-in Magnet), Mounting: U (Rod Trunnion), Type: N (Rubber Bumper), Bore: 40mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 25mm, Rod End Thread: Rod End Male Thread

Pad Diameter: ø16, Pad Type: B (Bellows), Pad Material: N (NBR), Buffer Specifications: JB (Rotating, w/Bushing), Stroke: 15mm, Vacuum Inlet: B5 (M5 x 0.8, Female Thread)

Magnet: D (Built-in Magnet), Mounting: T (Head Trunnion), Type: N (Rubber Bumper), Bore: 20mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 150mm, Thread: F (Female Rod End), Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9PW--Solid State, 2-color Indication, 3 Wire PNP, Horizontal, Lead Wire or

Magnet: D (Built-in Magnet), Mounting: F (Rod Flange), Type: N (Rubber Bumper), Bore: 40mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 25mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: M9BW--Solid State, 2-color Indication, 2 Wire, Horizontal

Magnet: D (Built-in Magnet), Mounting: B (Basic), Type: N (Rubber Bumper), Bore: 32mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 300mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: No Switch, Lead Wire or Prewire Connection: 0.5m (Or None in the Case of No Switch), Number

Sensor Range: 3 [For Compound Pressure (-100~100kPa)], Port Size: 02 [R1/4 (M5 Female Thread)], Output Specifications: L2 (IO-Link/Switch: 1 output + 2 outputs), Lead Wire: N (None)