LEJ-OM004xx Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
(Not a\ailabl on NCRBI BWl0) x ( ) : When porl A is pressunzed. x x Optional M3 fiiing available S ho/r lo ofder page NCDRBIOWIQoI$ol[r$Q Rotation Time Setting Bodg To k Used As A Flange ltcRElB\ltfto Actual Torque Even a small torque generated by the rotary actuator, due to inertia, can cause damage. Therefore.
A A A B A B P1 B B Section A-A (ejector) Section B-B (solenoid valve) Replacement parts list Parts list No. 1 2 3 4 5 6 7 8 Description Material No. Description Part No.
single: VZA4141-01 02 Pilot port (A side) M5 x 0.8 body side 2 x 4.5 Mounting hole Pilot port (A side) (R1, R2 port) (P , A, B port) 2 x Rc 18 3 x Rc , 18 14 2 x M5 x 0.8 sub-plate side 2 position double: VZA4241-01 02 Pilot port (B side) Body side Pilot port (A side) 2 x M5 x 0.8 body side 2 x 4.5 Mounting hole 2 x Rc 18 18 14 3 x Rc , 2 x M5 x 0.8 sub-plate side Pilot port (A side) (R1
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Enlarged view of part A A 0 3 Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
Also, keep the manual where it can be referred to as necessary. Piping Warning 1. To screw a piping material into a component, tighten with the recommended tightening torque while holding the female thread side. Operating Environment If the tightening torque is not enough, looseness and seal failure can occur.
Replace the product with a new one right away when it reaches its life. Make sure to verify the operating conditions of the actuator at least once a day.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
a place that will be used as a scaffold during piping.
The filter was packed in anti-static closing double packaging in a clean room and the inner package should be removed in a clean environment (clean room, etc.). 2 Install a dryer, mist separator, micro mist separator, super mist separator, odor removal filter, etc. for the air source used for the SFD series. 1) The SFD series is not available for compressed air containing a liquid such as
Released Workpiece 1 Workpiece 2 Workpiece n Atmosphere A B 4 Max. A: Max. pressure value when a workpiece is adsorbed. ON = A A B 4 Min. B: Min. pressure value when a workpiece is not adsorbed. OFF = B + 16-2-21 8 Series ZSE40/ISE40 Calibration Procedures Auto Preset (In the case of confirming the supply pressure) 1. Auto preset mode 2. Preparation for auto preset 3.
For information on related items, such as directional control equipment and drive equipment, refer to the caution sections in each respective catalog. 2. If there is vibration, the needle for flow adjustment of valve may be loosened. To prevent from loosing, a lock nut type is available. Confirm the part number. 1. Clean suction filters and silencers on a regular basis.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
M3x30 screw for connection to the valve manifold NS MS PWR PWR(V) WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
Contents Bore size (mm) NBR NBR 12 12 12 12 Bumper A Bumper A Bumper A Bumper A Resin Resin Resin Resin 12 12 Bumper A Bumper A Resin Resin 13 !4 13 !4 13 !4 13 !4 Bumper B Bumper B Bumper B Bumper B Resin Resin Resin Resin (Only 63 is common to the bumper A.) (Only 63 is common to the bumper A.) 13 !4 13 !4 Bumper B Bumper B Resin Resin (Only 63 is common to the bumper A.)
Contents Bore size (mm) NBR NBR 12 12 12 12 Bumper A Bumper A Bumper A Bumper A Resin Resin Resin Resin 12 12 Bumper A Bumper A Resin Resin 13 !4 13 !4 13 !4 13 !4 Bumper B Bumper B Bumper B Bumper B Resin Resin Resin Resin (Only 63 is common to the bumper A.) (Only 63 is common to the bumper A.) 13 !4 13 !4 Bumper B Bumper B Resin Resin (Only 63 is common to the bumper A.)
In the case of common exhaust type, exhaust air from both sides of R port as well. A port size Symbol Port size Exhaust style Individual exhaust Common exhaust 01 1 8
Also, no button operation for a certain period will turn off the power supply. (For details, refer to Auto power-OFF function.) Turn off the power supply after using the product to keep the life of batteries as long as possible. Return to a condition without charge, and retry zero clear operation. Do not operate in an atmosphere containing flammable or explosive gases.
Use protective tools such as anticorrosive gloves to avoid a burn or other human injury w hen touching the pump for check. A t stop E xhaust the air on the S UP side if the pump w ill be stopped for a couple of hours. C lean inside the pump to avoid clotting of transported liquid and sticking of internal parts if it w ill not be used for a long period of time.