Multi-channel Digital Sensor Monitor Display value fine adjustment (function) E A code number displayed to identify the error code detected by the self-diagnostic function of the product. Refer to "Error indication function" on page 77 for details of the errors. Error displayed Switches the switch output to ON/OFF when an error is displayed. Refer to "List of output modes" on page 39 for operating conditions.
E: Measurement laws are added. F: Contents are added. G: Contents revised in several places. H: Contents revised in several places. [June 2018] I: Contents revised in several places. [March 2020] J: Contents revised in several places.
[Torque : Less than 0.1Nm] Push-turn lever locking type [type E] While pressing, turn in the direction of the arrow. If it is not turned, it can be operated the same way as the non-locking type. Locked position Caution When locking the manual override on the push-turn locking types (D,E), be sure to push it down before turning.
[Torque: Less than 0.1 N.m] Push-turn locking lever type [Type E] While pressing, turn in the direction of the arrow. If it is not turned, it can be operated the same way as the non-locking type. For use in extremely dirty environments where there is the possibility that dust could enter the pilot exhaust and damage the valve.
E: Change of page number. (page 9) F: Contents revised in several places. G: Contents revised in several places. H: Contents revised in several places. [July 2018] I: Contents revised in several places.
Digit (Minimum setting unit) E Error indication With the self-diagnostic function of the Pressure switch, this indicates that there is an error which could cause a switch failure. F Fine adjustment mode Refer to "Fine adjustment of display value". A displayed pressure value can be adjusted within the range of 5% R.D. (5% of the displayed value).
A B C D E F G H LAT3-10 10 49 4 60 50 4 10.5 LAT3-20 20 69 6 25 90 80 14 20.5 LAT3-30 30 89 6 25 120 110 24 30.5 13 - LAT3-50 Note 1) Refer to Mounting screw specifications and tightening torques in section 4.3 Mounting (P.24). Note 2) The length of the part of the dowel pin inserted into the positioning hole should be shorter than the specified depth.
E: Contents revised in several places. F: Contents revised in several places.
In such cases, human injury may occur: e. g., by catching hands or feet in the machinery, or damage to the machinery itself may occur. 9. Consider actions when operation is restarted after an emergency stop or abnormal stop. Design the machinery so that human injury or equipment demage will not occur upon restart of operation.
Type T: 6 to 8 mm Type E: 2.3 to 2.8 mm Although A-,B+ and Bmarks are indicated on the Type D: 6 to 8 mm terminal block, this can be used as either +COM or Type Y: 4.5 to 7 mm -COM.
Type E, T, D, Y: In the case of DIN terminal block and terminal block, there is no polarity of positive [+] and negative []. Connect no. 1 and no. 2 terminals with corresponding power side. Applicable cable O.D.
Automatic cleaning unit E Part F Cleaning arm Cleaning arm View E Arrow D-shaped part Part C A Approx. 1 mm Motor shaft mounting part Part B 22 Doc. No.: IZ-OMR0035 4-5. Replacement of Emitter Cartridge If the emitters are worn out or damaged, replace the emitter cartridge. Before replacing the emitters, make sure that the power supply is OFF and confirm that the fan motor stops.
E: Contents are added. F: Measurement laws are added. G: Contents are added. H: Contents revised in several places. I: Contents revised in several places. [June 2018] J: Contents revised in several places.
Finger assembly Piston assembly MHZA2-6H MHZA-A0607 Main body of adaptor Mounting screw for adaptor Seal MHZA2-6K MHZA-A0608 Endboss assembly MHZA2-6M MHZA-A0609 MHZA2-6E MHZA-A0610 The end boss assembly other than type E should be mounted on the special body. Replacement part/Grease pack part no.: GR-S-010 (10 g) 15 - 3-6.
d u c e r B u s h i n g D i m e n s i o n s A Tthread 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/8 NPT 1/8 NPT 1/16 NPT 1/4-28 3/8-24 B Hex 9/16 9/16 9/16 9/16 9/16 9/16 7/16 7/16 5/16 5/16 7/16 C Thread 10-32 10-32 1/16 NPT 1/8 NPT 1/16 NPT 1/8 NPT 10-32 1/16 NPT 10-32 10-32 10-32 D Height 3/4 1/2 1/2 1/2 3/4 3/4 9/16 9/16 17/32 17/32 1/2 Part # RB 1/4-10 RB 1/4-10 Short RB 1/4-1/
3 MUB40-PS Hard anodized Aluminum alloy Cylinder tube e MUB50-PS Chromated Aluminum alloy Piston r MUB63-PS Hard chrome plated Carbon steel Piston rod t Seal kit includes !1 to !3. Order the seal kit, based on each bore size.
A One-touch fittings KP series B Dimensions (mm) Model A B C SFE4G 6 68.5 16.5 SFE5H 8 79 20.5 SFE7J 10 89 24 Bracket SFE-BR3 14 5 3.4 (15.5) 12.5 5.4 5.4 14 24 (20) SFE-BR4/5/7 B C (J) H D (F) G A E E Dimensions (mm) Model A B C D E F G H J SFE-BR4 30 16 7 4.5 7.5 (24.5) 17 15.5 (19.5) SFE-BR5 30 10 8.2 4.5 8.1 (29) 20 18 (23) SFE-BR7 34 14 7.35 4.5 9.8 (35) 24 20 (27.3) ( ): Reference dimensions
energy computation Stroke (mm) Example) Cylinder CDQ2B180-100DCM Load weight 10kg Piston speed 100mm/s = 0.1m/s Computation of m2 Note: 1in = 25.4mm 1N = 0.2248lbf 1kg = 2.2046lb 1J = 0.7375ft.lb Basic weight Additional weight 3.48kg 0.08kg 0.74kg Total 4.30kg CQ2B180-100DC Built-in magnet Rod end male threads Computation of E E = = 0.0715J (4.3 + 10) (0.1) 2 21 World Wide Support...
6 q e r t !5 w !4 !0 u y 32 to 50 With auto switch (built-in magnet) !6 q e r t !5 i o !1 !3 !2 !7 w !4 !0 u y Description No.