IDX-OM-W037 ILS PTC Starter(Start Relay) PTC Magnetic Contactor MC THS Thermostat TB Terminal Block Temperature Controller TC Temperature Sensor TS Solid State Relay SSR Heater H Fuse F Ground Fault Circuit Interrupter GFCI Programable Logic Controller PLC 64 IDH Series 6.4 Electrical Wiring Diagrams IDX-OM-W037 Thermo-dryer 6.
Warning Contact B OUT2 W&F An alarm is raised. OUT1 to OUT6 [Numbers following OUT1 to OUT6 refer to P1/P2 contact signal connector pin numbers.] Fault Fault alarm is raised. Fault Contact B OUT3 Warning Warning alarm is raised. Flow OK Circulating fluid reaches a flow rate required for operation. 3 Remote Contact A OUT4 Ready RDY lamp on the Main screen comes on.
(N) Lateral load F (N) Fig. 2 Relation between Lateral load and operating pressure 5 - 7.
No.0 No.1 No.2 No.3 No.4 No.5 No.6 No.7 No.8 No.9 End plate AXA DY#E DY#B DY#B DX#D DX#D DX#D DX#D DM#F SEN -79No.EX-OMS0027 (6) When unit diagnostics is generated, the diagnostic information is displayed on the [SYSTEM CONFIGURATION STATUS] screen. The unit which requires a diagnostics can be specified.
Definition and terminology Terms Meaning F Abbreviation for full span and full scale; means the maximum fluctuation range of the Pressure switch rated value. For example, when the output voltage is 1 to 5[V], the F.S. will be 5-1 = 4[V]. (Reference: 1%F.S. = 4 0.01 = 0.04[V]) F.S.
IDU Series 6-2 Refrigerant with GWP reference 6 2 IDX-OM-W028 Air Dryer 6 References 6-3 External Dimentions IDU22E75E PORT SIZE AIR OUTLET PORT SIZE AIR INLET A (G) B (D) E SWITCH EVAPORATION WITH LAMP THERMOMETER VENTILATION VENTILATION DRAFT AIR OUTLET BALL VALVE (F) AUTO DRAIN C DRAIN TUBE TERMINAL LENGTH:1m) (O.D.10, BLOCK J P K L2 N1 M 13 4x POWER SUPPLY ENTRY 911)[OPPOSITON] (WIRE
IDU Series 6-2 Refrigerant with GWP reference 6 3 IDX-OM-W013 Air Dryer 6 References 6-3 Dimentions IDU3E / IDU4E / IDU6E Evaporation Illuminated thermometer switch Q3 B3 E D A3 P Compressed air inlet Port size Compressed air inlet Port size F G Inspection Grille [200V AC Inspection Grille specification] Terminal block C3 Ventilation direction Ventilation direction Ventilation air outlet
ZB-OM00201-B Manifold Specifications With supply valve/ release valve, Without pressure sensor/ vacuum pressure switch Ejector PV=PD ZZBZB31-K1Station D side U side Atmospheric vent port Atmospheric vent port Supply valve Supply valve Release valve Release valve With supply valve/ release valve, with vacuum pressure switch Ejector PVPD ZZB-SM5 ZB31-Q1L(O) D side U side Station E F Vacuum
F: Limited warranty and Disclaimer are added. G: Contents revised in several places. H: Contents revised in several places. Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2009-2015 SMC Corporation All Rights Reserved No.EX-OMI0003-H
When the external switch signal is not used, cut the semi-strip processing section to prev ent the conductor f rom making contact. Power supply cable wiring No. Signal name Identification Pin colour Description 2 4 1 DC(+) Red Connect the power supply(+) of the product 2 External switch signal Note) White Blow starts by connecting with DC(-) 3 F.G.
Locations where strong magnetic or electric fields are generated. f. Locations where direct vibration or impact is applied to the product. g. Areas that are dusty, or are exposed to splashes of water and oil drops. h. Areas exposed to direct sunlight (ultraviolet ray). i. Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease.
HRZ Series 3.3 Procedure for Installation 3-11 M a i F HRX-OM-I051 Chapter 3 Transporting and Installation 5. Loosen the cap and insert the power cable from the power cable access. 6. Connect the communication cables with P1 and P2. P1 (D-sub 25P female) Cap P2 (D-sub 9P female) P3 (D-sub 9P male) Not used.
PTFE Grease Specification Standard models -X446 Grease pack part number: GR-F-005(5g) Lubrication Caution 1) Lubrication for products using special grease Lubrication to this cylinder leads to operation failure. If grease other than those specified is used, it may cause the operating failure. 2) Do not wipe off the grease on the sliding surface of the air cylinder.
The rubber back of the belt is softened and sticky. f. Crack on the back of the belt 36 - 2. For internal check, follow the below procedure. a. Loosen the bolts of the band holder on the end side of the actuator. Please take care to not cut hand on the edges of the Dust seal band. b. Remove the Seal band pusher and the Blanking plate.
HRW Series 3.3 Procedure for Installation 3-9 M a i F HRX-OM-K003 Chapter 3 Transporting and Installation 5. Loosen the cap and insert the power cable from the power cable access. 6. Connect the communication cables with P1 and P2. Cap P1 (D-sub 25P female) P2 (D-sub 9P female) P3 (D-sub 9P male) Not used.
Specifications 2-1 How to Order Z F C Body size Option Symbol Body size Filtration Nil None area B With bracket Applicable tubing O.D. Metric size 2 1 5 L/min 140 mm 2 3 10 L/min 470 mm Symbol Applicable 2 tubing O.D.
As this product has pressure balanced construction, the exhausting direction is free. 8 XL*-OMI0013-B 5.Dimensions 26 41 K J 72 53010 OPERATION INPUT K J V L C B 39 C B 69 XLS-**-P*G (with control power supply) XLS-**-P*G () L G1/2 D XLS-**-** (without control power supply) DIN terminal (D) DIN( D ) XLS-**-** () E D F K2 J L 27010 J M 29010 J K 33 25 G1/2 G1/2 C G C C B B B A A Terminal (
Exterior dimensions C D XMA Series Angle Valve Fd Fn Fc C Fc L1 KF Flange K Flange CF Flange ( K ) ( K F ) ( C F ) L2 H B G A A Unit:mm Model n Fd Fc H P.C.D L1 L2 XMA-16 40 103 38 1 30 34 17 40 P.C.D 27 6x4.4 XMA-25 50 113 48 1 40 26 39 XMA-40 65 158 66 2 55 70 41 63 P.C.D. 58.7 6x6.6 XMA-50 70 170 79 2 75 52 68 XMA-63 88 196 100 3 87 95 114 70 69 P.C.D. 92.1 8x8.4 XMA-80 90 235 117 3 114
Series MHR3 11223 Finger Rotary Actuated Air Gripper Size: 10, 15 Air Preparation Equipment Pressure Control Equipment Flow Control Equipment Pressure Switches/ Pressure Sensors Directional Control Valves Air Grippers Modular F. R.
MS-5H-4 MS-5H-6 15.5 16.5 7 8 1.8 2.5 7 8 6.5 8.5 Width across flats B Hose Elbow: MS-5HLH-4/6 Weight (g) 4.2 6.2 Effective area (mm2) 1.4 2.5 B Model L A C D E F M N Width across flats 7 MS-5HLH-4 MS-5HLH-6 15.8 17.8 12 13.5 7 8 8.5 9.5 1.8 2.5 7 8 6.5 8.5 15 16 5.5 6 Universal Elbow: MS-5UL Universal Tee: MS-5UT Width across flats 7 Width across flats 7 Effective area: 2.4 mm2 Weight: