(P=0.7MPa, P1=0.5MPa) (2) (mm2)Air exhaust side eff. area S ( P2=0.5MPa) (2)P/AP/BA/EAB/EBARB350VS7-8A1.5MPa1.0MPa0.1 to 0.83 MPa5 to 60oC1/80.83403160 mm253 mm2
JSY1000/3000/5000 Series (Plug-in) (Note that double, 3-or 4-position valves cannot be used for manifolds blocks with single wiring specification S .) Substrate inside Manifolds 30 The substrate inside of manifolds cannot be taken apart. Attempting to do so may damage parts. 36 Caution Fixation of DIN Rail Mounting Type Manifolds 1.
0.70.8 Nm M42 M42 0.70.8Nm n()10 -15No.EX-OMN0029CN-D DIN (SY SY ) (1)6 (M4X6)(EX600-ZMB2) 2 EX600 0.70.8 Nm (2)(M4X14)(EX600-ZMA2)2 0.70.8 Nm EX600-ZMA2 EX600-ZMB2 (3)DIN DIN (4)DIN (5)(M4X20)(EX600-ZMA2) 0.70.8 Nm DIN DIN EX600-ZMA2 -16No.EX-OMN0029CN-D M12 M8 M12 SPEEDCON SPEEDCON (1)(/)BA (2)C (3)B180(1/2) (1) (2) (3) A B C (EX600-ZT1) -17No.EX-OMN0029CN-D SI EX600-S
Grease pack part no.: GR-S-010 (10 g) 13 A
Manifold with Stainless Steel Plate: S, Model: 51S (EX260), SI Unit: EAN (Negative Common, PNP; EtherNet/IPâ„¢; 32 Outputs; M12 Connector), Wiring Type: S (All Single Wiring), Valve Stations: 24 (24 Stations, All Single Wiring), Port Size: N7 [4(A)/2(B) Port: ø1/4"; 1(P)/3(EB), 5(EA) Port: ø3/8"], Thread Type: One-touch: None; Thread Piping: Rc, Option: P (Trim Plate)
Grease pack part no.: GR-S-010 (10 g) 147
Element Relief valve P M 0 1 Paper Micromesh With relief valve None Hydraulic fluid 0 1 2 N W V Petroleum Water-glycol, Emulsion Phosphoric ester Note) N, W and V refer to the hydraulic fluid symbol indicated at the end of the element part number. Replacement Element Part No.
Grease pack part no.: GR-S-010 (10 g) 10 A
Grease pack part no.: GR-S-010 (10 g) 13 A
mm/s USB cable A-miniB type 100 500 100 500 1 1 200 1000 200 1000 2 2 50 200 50 200 3 3 CN2 Communication cable PC PC is prepared by customer) Refer to 8CN2 TB/PC Power supply connector(P.23) for usage.
u b a n k d r a i n p o r t Rotates 360.
L100mm, or stroke 1 2 Grease on the outer circumference Grease in the groove Rod seal part Approx. 3g About 1cm Amount of grease Fig. 5 Position for application of grease Table 1 Amount of grease Unit: g Stroke 40 P o s i t i o n f o r g r e a s e Bore size At 100st 3 to 4 50st added 1 19 3-2-4.
For safety, install an appropriate fuse and circuit breaker before use. 1) When using SMCs M5 fittings, follow the procedures below to tighten them. Connection thread: M5 First, tighten by hand, then use a suitable wrench to tighten the hexagonal portion of the body an additional 1/6 to 1/4 turn. The reference value for the tightening torque is 1 to 1.5 Nm 1.
Grommet, L/M Plug Connector DIN Terminal For AC Terminal Terminal Terminal Terminal (5) (1) There is no S type because the generation of surge voltage is prevented by a rectifier. Surge voltage suppressor of varistor has residual voltage corresponding to the protective element and rated voltage; therefore, protect the controller side from the surge.
Control Method: S (Meter-in, Light Blue), Stud Position: A (Right Side), Tube Diameter: 04 (ø4), Thread Type: R, Port Size: M5 (M5 x 0.8)
Control Method: S (Meter-in, Light Blue), Stud Position: A (Right Side), Tube Diameter: 06 (ø6), Thread Type: R, Port Size: M5 (M5 x 0.8)
Control Method: S (Meter-in, Light Blue), Stud Position: A (Right Side), Tube Diameter: 23 (ø3.2, Use 1/8" Tubing), Thread Type: R, Port Size: M5 (M5 x 0.8)
Control Method: S (Meter-in, Light Blue), Stud Position: B (Left Side), Tube Diameter: 04 (ø4), Thread Type: R, Port Size: M5 (M5 x 0.8)
Control Method: S (Meter-in, Light Blue), Stud Position: B (Left Side), Tube Diameter: 06 (ø6), Thread Type: R, Port Size: M5 (M5 x 0.8)
Control Method: S (Meter-in, Light Blue), Stud Position: B (Left Side), Tube Diameter: 23 (ø3.2, Use 1/8" Tubing), Thread Type: R, Port Size: M5 (M5 x 0.8)