Electric Actuator High Rigidity and High Precision Slider Type Circular arc grooves allow for high rigidity and high precision. Moment resistance*1 *2 61% Improved by up to Table displacement*1 50% Reduced by up to With internal battery-less absolute e Vibration resistance: No malfunction occurred in a test ranging between 45 to 2000 Hz. The test was performed in both an axial direction and a perpendicular direction to the lead screw.
For a product without an external stopping mechanism, if a directional control valve is closed to keep the air pressure in the product, in an attempt to stop the product at midpoint, it might not be possible to maintain that stopped position due to an air leakage.
Tighten the nut until it touches the end surface of the body, and then tighten it an additional 1/8 turn. If the nut wont turn any further, then it means a sufficient tightening has occurred.
PF2D Dimensions: Separate Type Display Unit PF2D30 -A Panel mounting type 0 1 Internal circuits and wiring examples z to , are terminal numbers. 40 41.8 OUT2 4.3 40.3 NC Sensor 8 Load 4 OUT1 Black Main circuit Main circuit 7 3 Load SMC FLOW SWITCH Brown + 6 2 35.8 36 Blue A 40 5 1 UNIT 12 to 24VDC Series PF2D5 RESET SET PF2D300-A(-M) Panel fitting dimension 3 x 7.2(=21.6) 8-M3 36 +0.5
Caution If a single power supply is used for both the motor control power and the motor drive power, or the power supply is an inrushcurrent protection type, a voltage drop may occur during acceleration/deceleration, which will generate an alarm.
Further more, conduct replacement using an IN, OUT differential pressure of 0.1MPa as a guide. 2) Start replacement after confirming that the temperature of the filter body is within a range of 0 to 40C. 3) When setting the element, be sure that it does not tilt inside the case. Adjust initial pressure drops to 0.01MPa to 0.02MPa or less. 6.
or less 30 or less 30 or less 30 or less 30 or less 50 or less 65 or less 30 or less 30 or less 30 or less 30 or less 40 or less 55 or less 40 or less 45 or less 40 or less 40 or less 40 or less ON OFF ON OFF AC Response time (ms) (at the pressure of 0.5 MPa) DC 55 or less 40 or less 45 or less 30 or less 30 or less Note) Based on dynamic performance test, JIS B 8375-1981.
BBA4 : For types D-C7/C8/H7 The above stainless steel screws are used when a type D-H7BA switch is mounted on a cylinder at the time of shipment. In addition, the BBA4 kit is attached when an auto switch unit is shipped alone.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 3 No.JXC-OMW1019-A LECP6 Series / Controller 1.
Mounting position Series Series Lead wire clamp Lead wire cap A 124.8 148.8 173.8 LP-01 ML1C ML1C LC-01 B 113.2 137.2 162.2 25 32 40 Mounting position Series ML1C 177.5 A 128.5 152.5 B 123.5 147.5 172.5 4.7-11
Calculating Acceleration/deceleration conversion example using an actuator with a 8 [mm] lead with an acceleration of 3000[mm/sec2].
Dimensions Padlock mounting position (Port size) (Port size) Standard specifications Model P1 P2 A B C D E F G H VHS20 1/8, 1/4 1/8 71.5 23 40 37 28 42 17.5 40 VHS30 1/4, 3/8 1/4 87 32 53 49 38 53 20 53 VHS40 1/4, 3/8, 1/2 3/8 111 42.3 70 63 52 71 29 70 1 0 - Revision history Rev. A Safety Instructions (Piping) corrected.
It results in generation of a play, increase sliding resistance or air leakage. Consult P/A for in case of usage in such an environment. 3.Install a shade screen if exposed to the direct sun light. 4.Install a blocking cover if a heat source is in the area.
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
(illodel) al D l H t wt wl 0E .tfit(B) 2.25 2.63 MlO x 1,0 .t2 N/A 0.34 1.95 .34 .40 /A l.t/A l{/A 0EII.r tm(B) 3.22 3.6r Ml2 x 1,0 t3 N/A 0.34 2.81 .43 .56 N/A .43 .38 (r.R)0rxr.25(Bl 3.22 3.59 y2.?
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. If using the product in an interlocking circuit.
Roller Lever Adjustable Rod Lever P3.5-40 P3.5-34.
) Oil (Standard) (D, E) High temperature oil (3) (S) (D) 99 100 183 AC DC AC DC 60 40 80 60 60 40 40 60 Maximum Minimum 1 10 5 (2) 10 (1) Note 1) Dew point: 10C or less Note 2) 50 cSt or less Note 3) D, E etc. in parentheses are option symbols.
DC AC, DC 60 40 1 80 60 10(1) 40 60 60 40 Maximum Minimum 10 5(2) Note 1) Dew point: 10C or less Note 2) 50 cSt or less Note 3) D, E, N, P etc. in parentheses are option symbols.
Series Construction ARP20(K)/30(K)/40(K) ARP20K/30K/40K (With backflow function) r q 1 I N e A 2 OUT A IN OUT t BLEED A-A w y Note Component Parts Material No.