Polyurethane Flat Tubing Series TFU Made to Order (Please contact SMC for specifications in detail, dimensions and delivery.) 10 m roll 50 m reel 100 m reel Model TFU0425 TFU0604 TFU0805 TFU1065 TFU1208 1. Change of color (10 m roll) 4 Tubing O.D. (mm) 6 8 10 12 Suffix -X4 to the end of part number. Ex.) TFU0604BU-2-10X4 2.5 Tubing I.D.
Withstand pressure 600 kPa Detection nozzle 1.5 *3 Consumption flow rate 5 L/min or less 12 L/min or less 22 L/min or less Power supply voltage 24 VDC 10%, Ripple (p-p) 10% or less (With power supply polarity protection) Current consumption 25 mA or less Switch output 1 output (NPN or PNP) Maximum load current 10 mA Maximum applied voltage 26.4 V Residual voltage 1 V or less (at 10 mA) Short
It converts air pressure to an equivalent hydraulic pressure, and this hydraulic pressure is used for operating an actuator, thus solving the problem that is associated with the compression characteristics of air.
Note) Use M5 female thread when piping onto a panel. 14-11-10 10 Pressure Gauge Guide Pressure Gauge for Clean Series (10-series) O.D: 44 G49 Installation of a filter on the breathing hole (filtration 3 m) enables an unit to curb particle generation from the pressure gauge inside. Standard Specifications G49 Back side thread R Air 3% F.S.
10 H 0 10 20 30 40 50 0 10 20 30 40 50 Gripping point L Gripping point L mm Gripping point L mm MRHQ16 MRHQ16 Internal gripping 60 60 50 50 Pressure 0.2MPa Pressure 0.2MPa 40 40 Overhang H mm Overhang H mm 0.3MPa 0.3MPa 0.3MPa 0.3MPa 30 30 0.4MPa 0.4MPa 0.4MPa 0.4MPa 0.5MPa 0.5MPa 0.5MPa 0.5MPa 20 20 0.6MPa 0.6MPa 10 10 0 10 20 30 40 50 60 0 10 20 30 40 50 60 Gripping point L mm Gripping
The speed will be approximately 1.4 times the date given on page 10-17-3.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4.
Install an air filter, if necessary. Install air filters close to valves on the upstream side. Install an aftercooler or air dryer, if necessary. Compressed air that contains excessive drainage may cause malfunction of valves and other pneumatic equipment. To prevent this, install an aftercooler or air dryer, etc.
l/s Note 2 5 14 45 80 160 200 Internal 1.3 x 10-10 for the standard material (FKM) at ambient temperatures , excluding gas permeation Leakage Pa m3/s External 1.3 x 10-11 for the standard material (FKM) at ambient temperatures , excluding gas permeation Flange type XMA KF(NW),CF KF(NW) KF(NW),CF KF(NW) KF(NW),K(DN) KF(NW), K(DN) ,CF XYA KF(NW) KF(NW) KF(NW) KF(NW) KF(NW) K(DN) K(DN) Main
The 10 LED display indicates the current operating DewPoint, shown by means of a three colours (bluegreen-red) bar over the display itself. Blue section the operative DewPoint of the dryer is too low: freeze risk ; Green section operating conditions ensuring an optimal DewPoint ; Red section DewPoint of the dryer too high, the treatment of the compressed air may be improper.
Fig. 9 Normal output OFFt0 Fig. 10 Sequence OFF0 Fig. 11 Sequence 6. Cascade connection There are only outputs up to 10 points (6 points in the case of VXFC06A) on a single board. However, it is possible to increase the output points by cascading (multiple board connection).
Specifications Table 4 Model Note 1 XMH-16 XMH-25 XYH-25 XMH-40 XYH-40 XMH-50 XYH-50 Flange (valve) size 16,CF034 25 40,CF070 50 Actuating type Manual Fluid Inactive gas under vacuum Operating temperature oC 5 to 150 Operating pressure Pa (abs) Atmospheric pressure to 1 x 10-6 Conductance l/s Note 2 5 14 45 80 Internal 1.3 x 10-10 for the standard material (FKM) at ambient temperatures ,
C) In order to generate a clamping force from the state described in step B), insert an additional shim. The thickness of the shim changes depending on the arm length and the operating pressure. Refer to page 8 to 10. Please note that the graph should only be used as a guide as there is a tolerance of about 10% in the clamp cylinder body.
Please contact SMC if an application under such conditions cannot be avoided. 10 One-touch fitting 10 One-touch fitting Component Parts Material AFD20 Zinc die-casted AFD30, AFD40, AFD40-06 Aluminum die-casted Note Description No. Platinum silver Body q Replacement Parts Part no. No.
W Water-cooled Radiating method 10 5.1 in (130 mm) x H7.1 in (180 mm) Liquid tank size Communication A B RS-485 RS-232C Liquid tank W HEB C H 10 002 C Round Shape of bath Option Nil N Rc1/4 NPT1/4 002 140 W Cooling capacity The option should be specified when ordering.
An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Mounting and Installation Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4.
An injury can result. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.