Direct Operated 3-port solenoid valve DIN terminal block 2) Insert rubber seal (6) and washer (5) into the cable entry on Applicable cord outside diameter D type: 6 to 8 mm Lead wire colour housing (2) in order, and tighten cable gland (4) securely. 3) Insert gasket (8) into the gap between the bottom of terminal box (3) and plug on the equipment, and insert screw (1) from the top of housing (2) to tighten them.
d (4)[][] -10- 8 2 6 3 2 () 5 2 2 (80-) (80-) 2 2 9 EXH 2 ON-OFF 1 1 7 2 2 2 No.
ISA-2-1 ISA-2-2 ISA-2-3 ISA-2-4 ISA-2-5 ISA-2-6 ISA-2-7 ISAl-1 ISAl-2/ISAl-1 ISAl-3/ISAl-2 ISAl-4/ISAl-3 ISAl-5/ISAl-4 ISAl-6/ISAl-5 ISAl-6 No.
Fluctuation of flow rate at the downstream side Set the pressure again. 2 The set pressure increases or decreases as time passes. Aging deterioration of the regulator Set the pressure again. Due to problem 2. Refer to problem 2. 7 Repeatability accuracy is bad. Due to problem 1. Refer to problem 1. Leakage due to deterioration of the rubber part. Consult SMC.
Note*) The bracket for IR1000 series is not compatibile with IR1000-A series Note 2) See pressure unit table below.
Refer to the table below if spacers are required separately. 2 Size 2 2 3 3 4.5 4 6 2 1/4 3 3/8 3 Size 3 3 4.5 4 6 2 1/4 3 3/8 Electrical entry DC AC Female thread type 1 Size 1 1 2 2 3 1 1/8 G Grommet 2 Size 2 2 3 3 4.5 2 1/4 *1 GS Grommet (With surge voltage suppressor) 3 Size 3 3 4.5 4 6 3 3/8 D DIN terminal (With surge voltage suppressor) Fitting type Face seal fitting/Compression
In this case "d" is displayed on the LCD. To reset holding, press the button again. 2. OUT1(1) set value input Pressing the button increases the set value. Pressing the button decreases the set value. Press the "SET" button to set the value and select the output OUT1(2) set value input mode. The set value of P2 is displayed.
VBA VBAT AP100 841 VEX13 Series 0 3 Specifications VEX1A33 VEX1B33 VEX113 0 3 VEX123 0 3 VEX133 0 3 VEX153 0 3 VEX173 0 3 VEX193 0 3 Model Port 1(P) 2(A) 3(R) M5 01 M5 01 01 02 01 02 03 02 04 04 06 10 12 14 10 20 1 8 1 8 1 8 1 4 1 8 1 4 1 4 3 8 1 2 1 2 3 4 2 1 1 1 1 1 Port size M5 M5 1 2 4 1 4 1 2 Operation Manual knob (Push locking slotted type) and Air operated type Manual knob (Push locking
, 3/4 Rc 1/4 5 Process Pump Air Operated Type (External Switching Type) Series PA3000/5000 How to Order 1 1 PA 3 03 3 PA3000 Body size Connection port size 03 04 06 3 5 3/8 (10A): PA3 1/2 (15A): PA5 3/4 (20A): PA5 3/8 standard 1/2 standard Liquid contact body material Thread type 1 2 ADC12 (aluminum) SCS14 (stainless steel) PA5000 Nil T F N Rc NPTF G NPT Diaphragm material 1 PTFE T, F,
(pilot air exhaust port) FLUID IN 1/2, 3/4 1/4 5 Series PA3000/5000 Process Pump Air Operated Type (External Switching Type) How to Order 1 1 PA 3 03 3 PA3000 Body size Connection port size 03 04 06 3 5 3/8 (10A): PA3 1/2 (15A): PA5 3/4 (20A): PA5 3/8 standard 1/2 standard Liquid contact body material Thread type 1 2 ADC12 (aluminum) SCS14 (stainless steel) PA5000 Nil T F N Rc NPTF G NPT
Default: Gain 9 Bit Bit 3, 2, 1, 0 Value 3 2 1 0 Setting Bit 0 0 0 0 Gain 0 0 0 0 1 Gain 1 0 0 1 0 Gain 2 0 0 1 1 Gain 3 0 1 0 0 Gain 4 0 1 0 1 Gain 5 0 1 1 0 Gain 6 0 1 1 1 Gain 7 1 0 0 0 Gain 8 1 0 0 1 Gain 9 1 0 1 0 Gain A 1 0 1 1 Gain B 1 1 0 0 Gain C 1 1 0 1 Gain D 1 1 1 0 Gain E 1 1 1 1 Gain F * indicates the initial shipping value. 3 Doc.No.DIT-69900-OM005-E Parameter index 0x43 Parameter
The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body.
The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Turn the power off and on again.