SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart.á An encloder makes it possible to confirm positioning and to output length measurements.á The LEHZ series is lightweight, and body sizes 10, 16, 20 and 25 are available with a compact motor size.Sealed-construction dust cover, Three types of
SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart.á An encloder makes it possible to confirm positioning and to output length measurements.á The LEHZ series is lightweight, and body sizes 10, 16, 20 and 25 are available with a compact motor size.Sealed-construction dust cover, Three types of
SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.
SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.
SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.
1/16" ID Barbs FMW-4103-39-W/K-P85 -13 - 20 PSI with Adjusting Knob and 1/8" ID Barbs
1/16" ID Barbs FMW-4103-39-W/K-P85 -13 - 20 PSI with Adjusting Knob and 1/8" ID Barbs
SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.
High Speed Pilot Operated Select an SMC connector cable (V100-49-1-m) or an FA sensor type connector with M8 threaded 3-pin specifications conforming to Nippon Electric Control Equipment Association Standard NECA4202 (IEC 60947-5-2). 2. Do not use a tool to mount the connector as this may damage it. Only tighten the connector by hand. (0.4 to 0.6 Nm) 3.
SET 20 VY1 + G P.SET PPA AL 14-11-19
ANR: 20C atmospheric pressure, relative humidity 65% 200 300 1,000 1 4 3 8 1 4 3 4 1 2 , , 0.12 AMC-EL2 BE20 0.2 AMC-EL3 BE30 0.5 AMC-EL5 BE50 VEX How to Order AN 5 1 0 AMC 06 AMC Thread Body size Suffix Port size 1 4 std. 3 8 std. 3 4 1 std. std. 1 2 2 std. 2 std. 3 5 6 8 9 B With bracket 1 2 14 20 1 1 02 Female Female Male Female Female Male 1 Male thread 10 1 4 Male Male Male D Drain piping
By removing the two retaining screws from the desired valves, and rotating each valve body 180 and reassembling it on the manifold base, it is possible to reassemble an N.C. valve as an N.O. valve. (When doing so, make sure that a gasket is attached to the mounting surface of the valve.) Properly tighten the screws. The tightening torque of the retaining screws is 3 Nm.
Regarding VP435 (3 position closed center type) Be aware that when the cylinder is in an intermediate stop state, if the supply pressure to the P port is discharged or decreased, this valve is constructed so that the pressure in the cylinder will be discharged to the P port, causing the cylinder to move. 7.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
The MY1W Rodless Cylinders have a one-piece carriage and piston that runs its entire stroke length housed with an inner seal belt to maintain air pressure combined with an outer dust cover for dustproofing and water resistance. A side seal option is available for added protection in harsher environments.
1 angle adjuster unit is required for retrofitting to an actuator without an auto switch unit.
When retrofitting to an actuator with an auto switch unit, 1 angle adjuster unit and 1 joint unit are required.
Sizes 20, 30, and 40 of the new CRB series released in November 2018 can be adjusted by ±5° on 1 side (start or end point) as standard.
・When connecting an AW□-D series regulator to an AC-B series modular F.R.L. unit, use the “Y□00T-D” spacer with brackets. This does not apply for AC-A series modular F.R.L. units.
・(Note) The current “Y□00T-A” spacer with brackets can be used for connecting AW series regulators from 2 generations before.
The MY1W Rodless Cylinders have a one-piece carriage and piston that runs its entire stroke length housed with an inner seal belt to maintain air pressure combined with an outer dust cover for dustproofing and water resistance. A side seal option is available for added protection in harsher environments.
SMC's E-MY2 series e-rodless actuators require no programming, and have both the operational ability of an air cylinder, and the speed controllability of an electric actuator.? The series consists of the E-MY2B (basic), E-MY2C (cam follower guide), E-MY2H (linear guide, single axis), and the E-MY2HT (linear guide, double axis) styles.?
SET 20 VY1 + G P.SET PPA AL 14-11-19