Metal One-touch Fittings Specifications 10 to 11 4. Troubleshooting 11 5. Construction 12 -1- Metal One-touch Fittings Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Model Thread size Tightening torque SX3000 M2 0.17 Nm SX5000 M3 0.8 Nm SX7000 M4 1.4 Nm 11 SX3000-OMM0002-B -12-SX3000-OMM0002-B -13SX3000-OMM0002-B TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
When these products are installed in equipment, provide adequate protection against noise by using noise filters. 11.
Fault No.11 Problem Possible cause Investigation method Countermeasures The inputs that are beyond the maximum point number do not operate. Check that the number of inputs has not exceeded the allowable number. The allowable number depends on the SI unit model. Inadequate total number of inputs from the Input block connected with the SI unit.
Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
How to Use . 11 2-1. Procedures to operation . 11 3. Wiring . 12 3-1. AC adapter type/ IZG10-01, 02 . 12 3-2. Power supply cable type/ IZG10-03 . 12 4. Function . 13 4-1. Name of parts . 13 4-2. LED indication . 13 4-3. Mode setting switch . 14 4-4. Emitter maintenance (cleaning and replacement) . 15 4-5. Alarm function . 17 5. Performance . 18 5-1.
Exhaust Port Exhaust Residual pressure exhaust button (2.9) Port -4- Warning Warning Design/ Selection Design/ Selection (11) Push the residual pressure exhaust button all the way to the end position by using a tool. Push the residual pressure exhaust button all the way to the end position by using a tool having a tip diameter of 2.8 or below.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.
Air Cylinder Speed controller Solenoid valve Regulator Air source Air filter Fig. 11 Basic Circuit 28 6.
And Adjust the offset voltage after supplying power. 23 Doc.No.IZ-OMK0015D (11) Timing chart Timing chart of normal operation Normal operation Reset operation Remarks Turn the power off to solve the problem, then supply power again. The error signal(OUT3) will be reset.
CONTENTS SAFETY 2 General General 3 positions 5 positions Model Indication Method 5 Names and Functions of Individual Parts 6 Installation 9 3 positions Names and Functions of Controller 11 Example of Internal Circuit and Wiring 12 Setting 15 Operation Characteristics 20 Specifications 21 5 positions Names and Functions of Controller 23 Example of Internal Circuit and Wiring 24 Setting 27
Order for tightening mounting screws 11 2-9-2. Auto switches When an auto switch is mounted or its set position is changed, refer to Fig. 4 to 11. C a u t i o n Use a specific mounting bracket (Page 19, Table 2) . Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDA).
AW20-B 11 AW20-B 0.80.1Nm AW30-B 17 AW30-B 2.350.3Nm AW40-B 21 AW40-B 3.50.3Nm Disassembly Remove the bowl assembly, housing, and element. Hexagon Remove a housing from a body by turning 4 mounting screws to the left with a hexagon wrench key. wrench key Nominal5 Remove the valve guide.
Operation and Mounting 2.1 Air Supply -P. 5 2.2 Operating Environment -P. 6 2.3 Design -P. 6 2.4 Mounting and Installation -P. 8 2.5 Piping -P. 10 2.6 Speed Control -P. 11 2.7 Shock Absorbing Mechanism -P. 11 2.8 Directional Control -P. 12 2.9 Mounting of Auto Switch -P. 13 3. Maintenance and Inspection 3.1 Inspection -P. 14 3.2 Maintenance -P. 14 3.3 Replacement Parts -P. 14 4.
Refer to Disassembly Drawing on page 11 for the part No. and the replacement procedure of the finger assembly and the body assembly. 15 - Construction/Parts list 2 MHF2-12D to 20D Components No. Description Material Note No.
Check if the dispersion is within the display accuracy range. 11 Product failure Replace the product. -52No.PS-OML0003-J Fault No. Fault Possible cause Investigation method Countermeasure Install a 5 m filter to prevent foreign matter from entering the pressure port. Also, clean the filter regularly to prevent drainage deposits.
Warranty period and guaranteed range 10 6.Parts replacement procedure 11 1 XM-OMP0001-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
SeriesNCQ8 Air Cylinder: Standard Type Double Acting, Single Rod Maintenance Parts 056 to 400 Construction Double Acting, Single Rod 10 11 9 Seal Kit Parts List No. 9 10 11 Description Piston Seal Rod Seal Tube Gasket Material NBR NBR NBR *BLUE links will lead to purchase pages. Repair Parts: Standard Seal Kit for Double Acting, Single Rod Remarks Bore size Kit no.