Mist Separator Regulator

to 60 oC (with no freezing) Proof pressure 1.5MPa Max. operating pressure 1.0MPa Without auto drain 0.05 to 0.85MPa Auto drain (N.C) 0.15 to 0.85MPa Set pressure range 0.1 to 0.85MPa Auto drain (N.O) 0.1 to 0.85MPa Max. air flow capacity Note 3) 150L/min(ANR) 330L/min(ANR) 820L/min(ANR) Filtration rating 0.3 m (99.9% filtered particle size) Outlet side oil mist concentration MAX.1.0mg/m3

DOC1013369

Size M3 was deleted from the table. Correction of errors 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2022 SMC Corporation All Rights Reserved

DOC1018150

When installing the product, use the mounting holes of the bracket bottom face and secure the product with M3 screws. The screws should be prepared by the user.) Tighten the screws to the appropriate torque for mounting the product. multiplication by 0.1 (= 1 0.9).

PSxx-OMM0006CN

13No.PS-OMM0006CN-E NPN () () ()()( ) () ON ON 0 (1 k 1 M A/D 5 V A/D 5(V)1(M)/(1(k)+1(M))4.995(V)0.005 V ) 30 ON-OFF ON () (P1LP1H P2LP2H)ON (30 ) () "digit" () 0 () SI ONOFF -14No.PS-OMM0006CN-E () () () () ON ON () (n1Ln1H n2Ln2H)ON (30 ) 30 (0FF)(ON)(OFF) (ON) () 5R.D.(5) (01 MPa 0.001 MPa 1/1000) () () "F" () ripple -15No.PS-OMM0006CN-E (4 2.5) (19 ) M35 L(2 )M45 L(2 ) M3

VP(A)300/500/700 Series (PILOT VALVE : V200)

Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.

EX250-SDN1(-X102)_eng

M3 hexagon screw Tightening torque: 0.6 N m Tie-rod Tightening torque: 0.6 N m EX250 No. 1 3 5 7 Side B No. 1 4 6 Side B Free Danger: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

EX250-SPR_eng

SI unit status information is as follows Tie-rod Tightening torque: 0.6 Nm M3 hexagon screw Tightening torque: 0.6 Nm 7 HW Contents Function Danger: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

m (95% filtered particle size)Maximum 1.0 mg/m3 (ANR) (approx. 0.8 ppm) (2)PolycarbonateStandard450.44

bar)]Recommended flow m3/min(ANR)Weight gAN500-061603212 or less165

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38

m (99.9% filtered particle size)800Max. 1.0 mg/m3 (ANR) ( 0.8 ppm) Note 4) Note 5)PolycarbonateStandardRelieving type1.38