SJ1000/2000/3000 Series Please consult with SMC, as there are some standard valve products that use fluorine grease for food processing equipment (NSF H-1). 4. Closed center For closed center, check the piping to prevent air 9. For the pilot EXH. (PE) port leakage from the piping between the valve and the cylinder.
Rubber seal, spool valve: Grease Please consult with SMC, as there are some standard valve products that use fluorine grease for food processing equipment (NSF H-1). Metal seal, spool valve: Turbine oil Turbine oil is applied to the spool valve of a metal seal type. Therefore, turbine oil may seep out when a new product is delivered, or while the valve is stored. 9.
To maintain good air condition, refer to "Air Preparation Equipment Model Selection Guide" in Best Pneumatics No. 5 and select the C or higher (D, E, F, G or H) level. (5) When a lubricator is used on the supply (upstream) side of the product, it can clog the fixed orifice, which may lead to operation failure. Never use a lubricator on the supply (upstream) side of the product.
The mounting position D-M9V D-M9WV D-M9AV D-M9 D-M9W D-M9A D-P3DWA Common Model A B E G A B E G L A B E G L D F H MHM-16D 9.1 9.1 4.6 5.6 8.1 12.8 11 MHM-16D1 *1 *1 *1 32.6 20.6 16.1 MHM-16D2 9.1 9.1 4.6 2.1 MHM-25D 14.6 14.6 10.1 4.6 7.1 17.5 17 MHM-25D1 *1 *1 *1 43.6 31.6 27.1 MHM-25D2 14.6 14.6 10.1 9.5 4.6 2.6 2.8 14.3 6 4 MHM-32D 19 19 14.5 3.8 6.3 22.5 23 MHM-32D1 *1 *1 *1 51.8 39.8
H Half duplex Communication system that sends and receives data in one direction at a time. I Idle Expression for PLC operation state. For details, Refer to manuals of each PLC maker. Depending on which PLC is used; the idle state might not be available. IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.
H Handheld Terminal (H.T.) Connected to the dedicated connector of the SI unit to adjust the internal parameters, monitor the status of all input and output signals, and turn on input and output forcedly. I Idle Expression for PLC operation state. For details, Refer to manuals of each PLC maker. Depending on which PLC is used; the idle state might not be available.
[August 2019] H: Modified errors in text. [ November 2019] I: Contents revised in several places.
Note 4) Barb fitting, barb elbow, barb elbow (H) are not compatible with water. Note 5) Deionized water is not recommended for use as it may affect the material used in the fittings In addition , it is known to degrade the water quality. Note 6) Do not use the universal nipples when N2 is used as clean dry air because universal nipples are pre-greased.
H Half duplex Communication method by sending and receiving alternately for bilateral communication. I IP address A 32 bit sequence of numbers assigned to identify individual equipment connected to a network. All connected to the network are given individual IP addresses. MAC address A number unique to equipment, connected to Ethernet. M MS Abbreviation of "module status".
D E F G H I ZS-31-X188 20 9 R1/8 R1/8 14 1.5 ZS-31-X189 20 9 NPT1/8 NPT1/8 14 1.5 ZS-31-X175 29 13 R1/4 R1/4 17 1.6 ZS-31-X186 29 13 NPT1/4 NPT1/4 17 1.6 -14No.PS-OMG0006-D Revision history A: For B: Complete revision C: Contents revised in several places. D: Contents revised in several places.
H Half-duplex Communication method that can send and receive data reciprocally in bi-directional communication. I Idle Base has received the FAIL SAFE command, and remains idle. The output state can be set to CLEAR, HOLD or Software Control using the parameter settings. IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.
Rubber seal, spool valve: Grease Please consult with SMC, as there are some standard valve products that use fluorine grease for food processing equipment (NSF H-1). 9.
H Handheld Terminal (H.T.) Abbreviation of handheld terminal. It is possible to monitor the input/output data and diagnostic data and set parameters. Idle PLC is in an idle state. EX600 system output will be constantly cleared. I IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.
To maintain good air condition, refer to "Air Preparation Equipment Model Selection Guide" in Best Pneumatics No. 5 and select the C or higher (D, E, F, G or H) level. (5) When a lubricator is used on the supply (upstream) side of the product, it can clog the fixed orifice, which may lead to operation failure. Never use a lubricator on the supply (upstream) side of the product.
H Handheld Terminal (H.T.) Connected to the dedicated connector of the SI unit to adjust the internal parameters, monitor the status of all input and output signals, and turn on input and output forcedly. I Idling A status in which the SI unit has received the FAIL SAFE command. The output can be cleared, held or forcedly switched on by setting parameters. ID No.
H The difference between the points when the Auto switch turns on and off, which is provided to prevent chattering. Hysteresis I Internal voltage drop The voltage applied between the COM and signal line when the Auto switch turns on. L Load current The current flowing to the load when the Auto switch turns on.
Bracket thickness is approx. 1.6mm Model Piping port size A B C D E F G H I J K L LFE13 3/8 90 73 40 23.5 56 83 89 24 6 1.6 96 87 LFE14 1/2 104 73 40 23.5 56 83 89 28 6 1.6 96 87 LFE26 3/4 105 78 50 29 67 94 100 35 6 1.6 115 106 LFE38 1 120 90 55 32 73 100 106 41 6 1.6 115 106 Model M N O P Q R S T U Bracket weight LFE13 48 39 4.6 12 11.5 52 28 2.5 depth 8.5 2 Approx. 45g LFE14 48 39 4.6
H Half-duplex Communication method that can send and receive data reciprocally in bi-directional communication. I Idle Base has received the FAIL SAFE command, and remains idle. The output state can be set to CLEAR, HOLD or Software Control using the parameter settings. IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.
Function selection mode H Hysteresis Difference between the ON and OFF points of switch output. Hysteresis mode Refer to the "List of output modes" on page 39. I Insulation resistance Insulation resistance of the product. The resistance between the electrical circuit and the case.
Enclosed or poorly ventilated environment. h. Locations which are exposed to direct sunlight or heat radiation. i. Areas where strong electromagnetic noise is generated, such as strong electrical and magnetic fields or supply voltage spikes. j. Environment where static electricity is generated to the product. k. Locations where strong high frequency is generated. l.