Series VQ4000 Base Mounted Plug-in/Plug Lead Single Unit For details about certified products conforming to international standards, visit us at www.smcworld.com. Note 2) Can be mounted on L kit only. For other kits, order E type control unit.
with a light, be careful not to damage the light with the cords lead wires.
An environment where food which will be sold as merchandize, directly touches the fitting components. Installable Splash zone An environment where food which will not be sold as merchandize, directly touches the fitting components. An environment where there is no contact with food.
Select the cylinder with bumper (O N") it cushion valVe is to be fuH yopened. Tie rods or piston assembly may be damaged if neither air cushion nor bumper is utilized.
Assembly 1) Terminal box (3) connected with housing (4) should be reinstated.
The element can be replaced with a single touch.
Operation of the product in an atmosphere containing any of these chamicals should also be avoided. A neutral detergent may be used for cleaning the bowl. 2. Avoid use exposed to direct sunlight. Maintenance OUT Caution IN 1. The element should be replaced after 2 years of use, or before the pressure drops to 0.02 MPa (0.2 kgf/cm2).
A contact protection box should be used in any of the above situations. Otherwise, the life of the contacts may be reduced. (They may stay on continuously.)
They can be ordered in lots of 10 pieces. d D Series SY3000 SY5000 SY7000 Part No.
When the cylinder is used as mounted with a single side fixed or free (basic type, flange type), be careful not to apply vibration or impact to the cylinder body. A bending moment will be applied to the cylinder due to the vibration generated at the stroke end, and the cylinder may be damaged.
Mount the solenoid so that it will be on the same side as the single solenoid of the Series VZ5000. In the case of base mounting, 2(A) port of 3 port valve should be 2(B) port of manifold base.
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
The size and the direction of the pipe port can be selected. The size of the electro-pneumatic proportion can be selected. Solenoid valves for actuating a 2 stage stroke gun cylinder or a clamp cylinder can be mounted on an integrated manifold (maximum of 8 stations). Stations Solenoid valves (8 stations at max.) can be added to the basic unit (2 stations).
Positioning should be performed accurately. Especially in the case of small diameter pads. 6. When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to a workpiece weight.
When leakage occurs from parts other than the piping, the product might be faulty. Disconnect the power supply and stop the fluid supply. Do not apply fluid under leaking conditions. Safety cannot be assured in the case of unexpected malfunction.
Because pipe fittings are press-fit, they must be replaced together with the cover assembly. r Those with a bore of 50 or more cannot be disassembled.
If these items need to be supported, provide an additional support. AMG q If red spots appear on the element surface, it is time to replace the element. Immediately replace it with a new element. Make sure to replace the O ring and the gasket together with the element. The element can be seen through the sight glass in front of the mist separator body.
(Line pressure) (The pressure differential of the solenoid valve unit must be no more than the maximum operating pressure differential.) 3. Withstand pressure The pressure which must be withstood without a drop in performance after returning to the operating pressure range (The value under the prescribed conditions).
PA Threaded for bottom mounting Spacial bracket can be mounted.
Actuation Warning 1 Normally closed q Cannot be used for vacuum retention. w Use a release valve. (Without a release valve, the workpiece may not be released.)