Magnetically Coupled Rodless Cylinder Low Profile Guide Type Series CY1F ø10, ø15, ø25 1 Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
12 19 23.5 B 13 15 14 19.5 A 14.5 12.5 19.5 24 B 13.5 15.5 14.5 20 B 7.5 9.5 8.5 14 B 10.5 12.5 11.5 17 B 7 9 8 13.5 20 25 32 40 Note) When setting an auto switch, be sure to check its operation before adjusting.
IEC 60204-1: Safety of machinery -Electrical equipment of Do not use in an explosive atmosphere. Do not expose to direct sunlight. Use a suitable protective cover. Do not install in a location subject to vibration or impact. Check the Maintenance of pneumatic systems should be performed only by qualified personnel.
Do not apply external force to the pilot valve. 14 SMC will investigate. The following information is required for investigation, so please send it to your sales representatives.
Do not operate at pressures or temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction. We do not guarantee against any damage if the product is used outside of the specification range. 2.
Do not apply external force to the pilot valve. 14 SMC will investigate. The following information is required for investigation, so please send it to your sales representatives.
Note 14) For an actuator with lock, add the power consumption for the lock.
A B A 14 A B A B A 14 A B A 14 A B 3 2 A 14 U side D side D side U side 0 1 5 4 2 3 B 12 B 12 B 12 B 12 B 12 7 8 1 2 3 4 5 Valve stations EX600-ED4 1 set EX600-WEN1 1 set EX600-EU1 1 set SS5Y3-10S6WE72-05B-C6 (Type 10 5-station manifold base, Wireless EtherNet/IP) Negative common, M12 connector IN/OUT pin arrangement 1, I/O unit: 2 stations * SY3100-5U1 3 sets (2-position single part no
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
Do not use at temperatures at or above the bo Do not use the product beyond the operating temperature range. Do not use at temperatures at or above the bo Do not use the product beyond the operating temperature range. Do not use at temperatures at or above the bo Do not use the product beyond the operating temperature range.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
Operation and Adjustment 13 to 14 8-1. Discharge from the product with drain cock 13 8-2. Manual drain discharge from the auto drain 14 9. Troubleshooting 15 10. How to Replace the Components 16 to 17 10-1. Bowl assembly Replacement 16 10-2. Element Replacement 17 11. Disassembly Drawing 18 12.
Operation and Adjustment 13 to 14 8-1. Discharge from the product with drain cock 13 8-2. Manual drain discharge from the auto drain 14 9. Troubleshooting 15 10. How to Replace the Components 16 to 17 10-1. Bowl assembly Replacement 16 10-2. Element Replacement 17 11. Disassembly Drawing 18 12.
Operation and Adjustment 13 to 14 8-1. Discharge from the product with drain cock 13 8-2. Manual drain discharge from the auto drain 14 9. Troubleshooting 15 10. How to Replace the Components 16 to 17 10-1. Bowl assembly Replacement 16 10-2. Element Replacement 17 11. Disassembly Drawing 18 12.
Refer to p.3.4-14. Auto Switch Mounting Bracket Part No.
Refer to p.3.8-14. Auto Switch Mounting Bracket Part No.
Recommended tightening torque [N-m] Thread 1/4 3/8 1/2 Piping Warning IN OUT port 12 to 14 22 to 24 28 to 30 EXH port 8 to 10 Do not apply any additional twisting, or bending moments except for the weight of the filter regulator itself. Provide separate support for external piping, as damage may otherwise occur.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Do not operate at pressures or temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction. We do not guarantee against any damage if the product is used outside of the specification range. 2.