Guide Table Series MGF ø40, ø63, ø100 1 2 y u !3 e q t r o w @0 !1 !7 !8 !9 !5 !6 !0 MX i MTS @4 MY CY MG @1 !4 @3 @3 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com When the cylinder is extended When the cylinder is retracted CX DDescription Material Note Component Parts Description Material Note No.
9 MNB e CNA2 $2 q %3 %4 $1 CNS #1 #0 @9 #4 $0 !5 !4 $7 $6 y %0 %1 CLS CLQ #3 #2 !8 @0 @2 @1 @7 RLQ @3 r MLU o #5 !6 $3 $4 MLGP Component Parts Component Parts Material No.
1 Output RoHS 3-Screen Display High-Precision Digital Pressure Switch IP40 ZSE20(F)/ISE20 Series How to Order Rated pressure range ISE20 0.1 to 1 MPa M For positive pressure ISE20 M5 N For vacuum/ compound pressure ZSE20 N M M5 q w e r t y u q Rated pressure range e Unit specification w Output specification ZSE20 0 to 101 kPa ZSE20F 100 to 100 kPa Symbol Description N NPN open collector 1
Valve element becomes free to incline and it reaches valve seat o. q Description Note Plated No. Material Cast iron Undercover Body Plated Cast iron Aluminum alloy w e Cover Plate r Iron t Stainless steel Valve element A Valve element B Piston Return spring y Stainless steel u Aluminum alloy i Piano wire o Stainless steel Valve seat !0 Stainless steel Rod !
7 Aluminum alloy Head cover y 80 to 100 Painted Ball bushing !8 Carbon steel Hard chrome plated NBR Piston seal !
Z directions for 2 hours each Vibration resistance Impact resistance Weight Enclosure Piping port size 490m/s in X, Y, Z directions, 3 times each 250g (8.8oz) (not including lead wires) Equivalent to IP65 1/8, 1/4 Note 1) The output functions (2 outputs OUT1 and OUT2) operate only with respect to the real-time flow rate display, and do not operate with respect to the accumulated flow rate
Fluid Passage Structure q r r No.
(Loosen in the case of Y-shape type terminal.) As shown in the below figure, mount a crimped terminal (9), and then again tighten the screw (3e). Note) Tighten within the tightening torque of 0.5 Nm15%. Note: a It is possible to wire even in the state of bare wire.
The load ratio is obtained by the following formula: ((Load weight x 9.8)/Theoretical output) x 100% Conditions Base piping Series CJ2 Series CM2 Series MB, CA Series CS1 T0604 x 1m Tube x Length Speed controller Silencer Tube x Length Speed controller Silencer Tube x Length Speed controller Silencer AS3001F-06 AN200-KM8 VQC1000 T0604 x 1 m T0806 x 1 m AS3001F-08 AS3001F-06 VQC2000 AN200-
From the point just found, draw a line to the Y-axis to find the air consumption. The result is approximately 9l/min (ANR). 1 0 2 3 4 5 6 7 8 9 10 Cycle (Hz) Caution 1. These flow rate characteristics are for fresh water (viscosity 1mPas, specific gravity 1.0). 2.
From the point just found, draw a line to the Y-axis to find the air consumption. The result is approximately 9l/min (ANR). 1 0 2 3 4 5 6 7 8 9 10 Cycle (Hz) Caution 1. These flow rate characteristics are for fresh water (viscosity 1mPas, specific gravity 1.0). 2.
From the point just found, draw a line to the Y-axis to find the air consumption. The result is approximately 9l/min (ANR). 1 0 2 3 4 5 6 7 8 9 10 Cycle (Hz) Caution 1. These flow rate characteristics are for fresh water (viscosity 1mPas, specific gravity 1.0). 2.
From the point just found, draw a line to the Y-axis to find the air consumption. The result is approximately 9 l/min (ANR). 5 1 0 2 3 4 5 6 7 8 9 10 Cycle (Hz) Caution 1.These flow characteristics are for fresh water (viscosity 1 mPas, specific gravity 1.0). 2.
End Plate Assembly > q U end plate assembly no.
R R: Gripping point distance [mm] 6 MHL2 Series Construction 10 16 to 25 e r t u w y @4 @0 @1 @2 !7 !5 !8 @3 !3 e o i q @6 @7 @3 @5 !9 !0 !2 !1 !6 !4 Component Parts No. Description Material Note 1 Body Aluminum alloy Hard anodized No.