MLGP (d: thread O.D.) 2d or more D By-pass port dia.
(d: thread O.D.) 2d or more D By-pass port dia.
There is a possibility of dangerous sudden action by air cylinders if sliding parts of machinery are twisted due to external forces, etc. In such cases, human injury may occur; e.g., by catching hands or feet in the machinery, or damage to the machinery itself may occur. Therefore, the machine should be designed to avoid such dangers. 2.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
ME 4O3LR-5 Assembty Kit. oo sTnugfloN Each of the manltold blocks and ths manlfold End Plates aro aftlxd to its adjacenl block by a unlqu pair ot "V" Clamp Platss h6ld together by two bolts and nuts.
Water condensed at this time will be removed from the air by an auto drain and drained out automatically. Air separated from the water will be heated by a cooler reheater (heat exchanger) to obtain the dried air, which goes through to the outlet side.
Air supply The compressed air supplied to the cylinder should be filtered by SMC AF series air filter and regulated to the specified set pressure by SMC AR series regulator. Warning Use clean air.
Prevent the seizure of rotating parts (pins, etc.) by applying grease. Do not use until you can verify that equipment can operate properly.
However, in case of size 1, the tubing cannot be changed by reducing.
The average velocity of the cylinder is what the stroke is divided by the total stroke time.
Deterioration by atmosphere Do not use the product in the presence of salt damage, sulfurous acid gas which makes the metal corroded, or solvent which makes the seal deteriorated. 3. Deterioration by ozone Do not use the product under the direct sunlight on the beach, or by the mercury lamp, or the ozone generator, because the rubber material will be deteriorated by ozone. 4.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. If a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged.
The governor establishes the outlet pressure by knob operation and pressure adjustment in the drive chamber by feeding back the outlet pressure.
At that time, the lower poppet valve y opens by the degree preset by the needle !1. (Counterclockwise rotation of the needle opens the poppet valve.)The upper and lower poppet valves operate independently.
The operating range is determined by the magnetic force of the magnet (range, in which the magnetic force acts) and switch sensitivity. So, the operating range may vary as these conditions are changed by the ambient environment, etc.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque.
The type which is applicable for using inside the clean room graded Class 100 by making an actuators rod section a double seal construction and discharging by relief port directly to the outside of clean room.
a spring force, which is further tilted by the load that is applied to the cylinder, thus locking the piston rod.
Press key ( di spl ayed al t ernat el y) Set P_3 by usi ng t he and keys. Change t he val ue by usi ng and keys. Press key ( di spl ayed al t ernat el y) Set P_4 by usi ng t he and keys. Change t he val ue by usi ng and keys. Press key Ret urn t o ( current ) pressure di spl ay.
Press key ( di spl ayed al t ernat el y) Set P_3 by usi ng t he and keys. Change t he val ue by usi ng and keys. Press key ( di spl ayed al t ernat el y) Set P_4 by usi ng t he and keys. Change t he val ue by usi ng and keys. Press key Ret urn t o ( current ) pressure di spl ay.