Title not found Orifice Fittings Many of our small brass fittings such as B1, B2, T1, T2, etc., are available as orifice fittings. In the case of Tees, the branch and/or one end of the run may be an orifice. A cross can have as many as three orifices. The general dimensions in this catalog are subject to change without notice 5/32 Couplings 7/16 1/2 15/16 1 5/16 5/16 Typ.
The length of the lead wires between the switch unit and contact protection box should be no more than 1m, and they should be placed as close together as possible. Tighten with a torque of 0.10 to 0.20Nm. As a rule, it should be turned about 90 past the point at which tightening can be felt.
If both plug and socket sides have connectors for SPEEDCON, the cable can be inserted and connected by rotating it 180, leading to a reduction in labor hours. A non-compatible connector can be connected to a compatible connector as well as an M12. 1. Be sure to turn the power off when connecting and disconnecting the connectors. 2. Do not touch the engagement surface with wet hands. 3.
Access them in the same manner as a programming Key.
When used vertically for applications, use caution as there is a possibility of dropping due to separation of the magnetic coupling if a load greater than the allowable value is added. Please contact SMC for the operating conditions (pressure, load, speed, stroke, frequency, etc.) before use. Refer to the WEB catalog (CY3 series model selection method) for details. 5.
/For force control responding to a slight pressure fluctuation Application examples for a single acting model Application example for a double acting model Polishing Base for fixing Two MQP applying pressure cylinders can improve the thrusting accuracy of a MQQ and a MQM double acting metal cylinder.
Reference dimensions of 10-32 UNF and NPT threads after installation. 586 Series AS1F-D Speed Controller Adjustable by Flat Head Screwdriver with One-touch Fitting Elbow Type/Universal Type Dimensions Universal type L6 D4 AS TMH ASD Applicable tubing O.D. d AS H D1 AS-FE KE (Hexagon width across flats) AS-FG AS-FP M1 AS-FM L3 AS-D AS-T AS-D AS-T A L4 ASP L5 D3 ASN AQ ASV AK VCHC L1 D2 ASS
Actuator drive When an actuator, such as a cylinder, is to be driven Provide ventilation when using a valve in a confined area, such as in a closed control panel.
Plugging one of the cylinder ports (A or B) enables use as a 3 port valve. lt should not be used in special applications such as use as a non-leakage valve. Make sure the exhaust port is open if used as a 3 port valve. Solenoid {X) represents plugged port. common Exhaust ifflg"o,BJ"". rnd Pilot valve I Exhaust air from pilot valve will flow to main valve exhaust port.
Especially in the case of small diameter pads. 6.When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to a workpiece weight. Use caution particularly when lifting items such as glass plates and circuit boards, because a large force will be applied by the wind pressure.
double (B) 2 (A) 4 (B) 2 (A) 4 Same manifolds as series SYJ3000 are prepared. 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) SS5YJA3 Fill the same as SS5YJ3 3 position closed center 3 position closed center (B) 2 (A) 4 (B) 2 (A) 4 Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) 3 position exhaust
V) Power supply voltage Communication type Communication protocol: Dedicated for SMC Communication speed : 750 kbps Current for input branch Max. 1 A per branch Power supply for input and controlling GW: Max. 4.1 A (Inside GW unit: 0.1 A, Input unit: 4 A) Power supply for output: Max. 6 A Current for output branch Max. 1.5 A per branch Rated current At 0.75 A per branch: 20 m or less At
40 60 80 100 Load N 0 20 40 60 80 100 Load N 0 50 100 150 200 250 Data 8-9-9 9 Series MXY Table Deflection Table deflection due to pitch moment load Displacement at A when load is applied F Table deflection due to yaw moment load Displacement at A when load is applied F Table deflection due to roll moment load Displacement at A when load is applied F A A F A F F L L L L dimension mm L dimension
L G ZA F H K J ZX I B C E D A ZR ZM 2 x M3 countersunk head screw mounting hole ZMA ZQ ZH ZU ZFC10, 20 ZL Applicable tubing O.D.
If this surface is to be used for mounting, a spacer composed of a non-magnetic substance (aluminum, etc.) is required as shown in the figure below.
As a rule, it should be turned about 90 past the point at which tightening can be felt.
Use caution, as there is a danger of being burned if a valve is touched directly. 2. Valves may reach high temperatures when continuously energized. Use caution, as there is a danger of being burned if a valve is touched directly. SOL. AC AC SOL. Without light AC SOL. Light With light 10 Series VCB Specific Product Precautions Be sure to read before handling.
Example: The figure below is based on the condition of set values as P1 = 40 [kPa] and P2 = 20 [kPa].
If the chewed portion of the tube is used as is, this can cause problems such as air leakage or difficulty in removing the tube. 2. When mounting a One-touch fitting, use a suitable wrench to tighten the hexagonal flats of the fitting. Moreover, position the wrench at the lower part of the hexagonal flats as close to the threads as possible.