Series MXP Precision Air Slide Table When you begin to feel that the screw is being tightened, turn it an additional 90.
Never remove valve at an angle.
Refer to page 100 for part numbers. 45 46 Non-standard Motor Series LJ1H10 Rolled Ball Screw High Rigidity Direct Acting Guide Motor Output 50W 12mm/12mm lead Horizontal Mount How to Order Stroke 1 LJ1H10 G NB 1 F W X10 Cable entry direction Top entry Left entry Power supply voltage Motor specification Cable entry direction Switch Matsushita Electric Industrial Co., Ltd.
An application which could have negative effects on people, property, or animals Compliance Requirements requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for 1.
(Assuming approximately 30% dispersion) There may be the case it will vary substantially depending on an ambient environment.
Also, BBA2 is included when an auto switch alone is shipped.
If the workpiece gripping point goes beyond the range limits, this will have an adverse effect on the life of the air gripper.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
If the workpiece gripping point goes beyond the range limits, this will have an adverse effect on the life of the air gripper.
Install an air dryer or after cooler on the upstream side of the pressure release 3 port valve because air containing excessive drainage may cause malfunction. Caution ! 1. Install an air filter of 5 m filtration on inlet side. 2. Install a mist separator on the inlet side to remove carbon powder from the compressor or other equipment.
A water resistant type cylinder is recommended for use in an environment which requires water resistance.
VF 74.5 VFR 39.5 VP7 VP4 Individual SUP spacer VVQZ1000-P-5-M5 VVQZ2000-P-5-01 VVQZ3000-P-5-02 M5: VQZ1000 Rc(PT)1/8: VQZ2000 Rc(PT)1/4: VQZ3000 VQ VQ4 B VQZ Used to form a separate supply port for an interior manifold station or stations.
AC circuit DC circuit VQZ100-12A (Standard) VQZ100-12B (External pilot) 2 mounting screws are included with each plate. 1 2 1 2 wA base mount VQZ100 valve can be converted to an individual in-line (body ported) valve by installing an adapter plate on the mounting surface of the valve.
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
individual EXH spacer assembly, an individual or an adapter plate assembly on VV5Z5-21P .
When removing drain is difficult, use of a filter with an auto drain is recommended. ITVX PVQ VY1 VBA VBAT AP100 3. Piping materials without flexibility such as steel tube piping are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. Caution 1.
When removing drain is difficult, use of a filter with an auto drain is recommended. ITVX PVQ VY1 VBA VBAT AP100 3. Piping materials without flexibility such as steel tube piping are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. Caution 1.
Furthermore, by connecting an input block, a maximum 32 sensor signal inputs are possible. SI unit for AS-i As a AS-i slave unit, this kit is capable of up to 4 or 8 points of solenoid valve ON and OFF control. Furthermore, by connecting an inmput block, a maximun 4 or 8 sensor signal inputs are possible.
individual EXH spacer assembly, an individual or an adapter plate assembly on VV5Z5-21P .
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.