Auto Switch Guide Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
Rubber bumper Cushion Mountable Auto switch Note 1) Operate without lubrication from a pneumatic system lubricator. Note 2) Use a low speed controller (Series AS-FM, AS-M) to adjust a speed. Refer to pages 10 through 17.
Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
Please consult with SMC if you use a fluid other than compressed air. 2. A protective cover is recommended to minimize the risk of personal injury. If a driven object and moving parts of a cylinder are in close proximity, personal injury may occur. Design the structure to avoid contact with the human body. 2.
With functions narrowed down, 2 independent temperature control systems have been achieved with only a single compressor , a single pump , and a single tank .
Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
Clean series 10 11 Relief type Vacuum suction type 10 C D M 2 R A 40 150 C73 21 C D M 2 R A 40 150 C73 Number of auto switches Mounting style 2 pcs. 1 pc.
7 @2 @3 @4 r y e #7 u o !1 i w !8 #4 !6 A @0 @1 !9 #2 !0 #1 A' For ball bushing #5 @5 #0 @8 !7 @6 !3 #8 !2 @1 !0 @9 For slide bearing y For long stroke For 100 @7 For 80, 100 View A-A' Parts list Parts list No. Description No.
Note 10 P523020-5 30 A set of above numbers r, !2, !3, !7, !
Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
In principle, this function counts each time there is a rise or fall in either of the A or B phase pulses. 2 1 Amplification/ Interpolation circuit Counter A phase B phase Magnetic resistance element Piston rod Magnet Count 1 2 3 4 5 6 7 8 9 10 .
Note 2) The above values should be used as a guide for detection at stroke end.
Excessive load will be applied to the piston rod, resulting in damage to the actuator and a reduced service life of the product. Model EQY16 EQY25 EQY32 Lead A B C H A B C H A B C Work load [kg] 1 1.5 3 1 2.5 5 10 2 4.5 9 18 9.
Seal guide B Slide plate Spacer Hexagon socket head cap screw Side seal unit MYMK-16-A MYMK-25-A MYMK-25-A MYMK-25-A MYMK-16-A Nickel plated Seal list 20 No. 12 13 14 15 16 17 18 19 20 Qty. 1 1 2 2 2 2 2 4 2 Description Material 16 25 32 63 40 50 MY20-16A-Stroke Seal belt Dust seal band Scraper Piston seal Cushion seal Tube gasket O-ring O-ring Special resin MY16-16A-Stroke MY25-16A-Stroke
2%4$2$4$5 @4 #0 Section A-A A A $0 $1 #4 #5 #2 @1 $6 $3 Parts list Parts list No. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 55 56 Description Cylinder tube Body Head cover WR Head cover WL Slide table Piston yoke Piston Wear ring Belt separator Parallel pin Cushion ring Cushion needle Belt clamp Cam follower Eccentric gear Gear fixture Adjustment gear Retaining ring
5 7 2 5 3 2 2 3 5 3 1 MHZ2-16 No setting 3 2 4 1 MHZ2-20 MHZ2-25 MHZJ2-10 No setting No setting MHZJ2-16 No setting No setting 3 2 1 MHZJ2-20 MHZJ2-25 Note) "" in the table indicates a skip with no dimension.
M6 thread depth 11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.