MWP_E MWP*-OM0020Q-B PRODUCT NAME Air Press Cylinder MODEL/ Series/ Product Number MWP Series Contents Safety instructions 2,3 ActuatorsPrecautions 48 Air Press Cylinder Specifications Specifications 9 Operation Principle 10 Relationship between the output and stroke 10 Installation and Handling Mounting Orientation / Installation 11 Application Examples 11 Cylinder Replacement 12 References 12,13
Also, if pipe tape is used, as in Fig. (11), leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating air Air supplied to the rotary actuator shall be cleaned by the filter. CRA1 series is lubrication free.
(Page 11) 7 1000 fR[N] 100 Lateral load applied to rod 100 80 63 10 50 40 1 0 500 1000 1500 Cylinder stroke [mm] Fig 1. Allowable lateral load applied to rod end C a u t i o n Be certain to align the rod axis with the load and direction of movement when connecting.
Coil 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Terminal no.2 (-) Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm. Note 3) Round or Y-shaped crimped terminal cannot be used.
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (such as the installation of a cover or the restricting of access to the product) to prevent potential danger caused by actuator operation. 11. Do not disassemble the product or make any modifications, including additional machining.
(The first digit of the lower level will start PV flashing.) 11. Press key change 20 to 30. SV 12. Press SEL key to set the value. 13. Press key to return to PV/SV display. SV 313 IDH Series 3.10 Functions and operation of temperature controller IDX-OM-W037 Thermo-dryer 4.
(See Fig.13) Replacement part: Shock absorber Bore size Part no. 32 RB1007-X225 4050 RB1407-X552 Lever Hexagon socket head set screw Push down Fig. 11 10 - Lever Shock absorber 11.Internal construction 12 16 Push down Replacement Grease applied Approx.5mm Fig. 12 Fig.13 20 11 - 32&50 Component Parts (12&50) 12 - Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81
Replace the product in the case of failure such as difficulty removing or inserting tubing. 11 - 5. Construction Male connector Male elbow No.
Maintenance 11 9. Mounting accessories (option) 12 10.
Since cylinders receive excessive force in such a case, do not design circuit synchronizing cylinders only. 11. Mounting Methods Various mounting methods are available as follows. Bottom mounting Side mounting 11-1. Cautions on Mounting 1) Never place your hands or fingers between the plate and the body.
Auto switches When an auto switch is mounted or its set position is changed, refer to pages 11 to 17. Caution Use a specific mounting bracket (Table 3 on page 12.) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque.
0.13 the values in the table 11. 20 0.24 Piston speed has to be less than the allowable value 25 0.45 32 0.88 40 1.53 23/28 6.
As shown in Fig. 11, hold the piston seal with one hand and push it into the groove so that the piston seal can be lifted off and pulled out without using a precision screwdriver. The groove of the rod cover is deep, so if the rod seal is removed with a precision screwdriver, it might be damaged. Fig 10. Remove rod seal Pinch and pull out Fig 11.
Refer to the Material Safety Data Sheet (MSDS) of the hydraulic fluid when supplying the fluid. 11 - 3. Maintenance 3-1. Precautions Warning 1. Maintenance should be performed according to the procedure indicated in the Operation Manual. If handled improperly, malfunction and damage of machinery of equipment may occur. 2. If handled improperly, compressed air can be dangerous.
The value of the residual pressure can be checked using the outlet pressure gauge. 11.
Also make sure that the rotational torque applied to the cylinder body does not exceed the allowable rotational torque (given on page 11). (Otherwise, the excessive rotational torque will damage the non-rotating mechanism and lead to a malfunction.) 6.
PP depth element Nominal filtration accuracy: 1 to 75m Material: PP EJ202S ... x 11 (L125) EJ302S ... x 11 (L250) EJ402S ... x 11 (L500) b Set the stopper on the retainer while holding down the V-band outside perimeter, and then tighten the wing bolt to the prescribed position.
Nil T F Rc NPTF, NPT G Caution 3 position closed center 3 position exhaust center Refer to pages 5-11-2 to 5-11-6 for Safety Instruction and Solenoid Valve Precautions. 5-3-1 2 Series VZA2000 Dimensions: Body Ported 2 position single: VZA2121-M5 2 position double: VZA2221-M5 2-2.8 mounting hole 2-2.8 Mounting hole Pilot port (A side) M5 x 0.8 Pilot port (A side) Pilot port (B side) 2-2.8
Made to Order Specifications (For details, refer to page 3-6-11.)
A 15 3 3 4 5 6 7 8 9 10 11 12 13 Station 5 16 17 18 19 20 21 22 23 24 25 SOL. B 16 SOL. A 4 Station 6 SOL. B DIN rail mounting bracket [-D] VVQ1000-57A for {F, L, M, P, S (EX500) kit} VVQC1000-57A-S for {S (EX250) kit} VVQC1000-57A-T for {T, S (EX126) kit} 17 SOL. A 5 Station 7 SOL. B 18 SOL. A 6 Station 8 SOL.