SMC Corporation of America
Elite Part Number Search
Search Results "HRW030-H-DNZ"

H Half-duplex Communication method that can send and receive data reciprocally in bi-directional communication. I Idle Base has received the FAIL SAFE command, and remains idle. The output state can be set to CLEAR, HOLD or Software Control using the parameter settings. IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.

Rubber seal, spool valve: Grease Please consult with SMC, as there are some standard valve products that use fluorine grease for food processing equipment (NSF H-1). 9.

H Handheld Terminal (H.T.) Abbreviation of handheld terminal. It is possible to monitor the input/output data and diagnostic data and set parameters. Idle PLC is in an idle state. EX600 system output will be constantly cleared. I IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.

To maintain good air condition, refer to "Air Preparation Equipment Model Selection Guide" in Best Pneumatics No. 5 and select the C or higher (D, E, F, G or H) level. (5) When a lubricator is used on the supply (upstream) side of the product, it can clog the fixed orifice, which may lead to operation failure. Never use a lubricator on the supply (upstream) side of the product.

H Handheld Terminal (H.T.) Connected to the dedicated connector of the SI unit to adjust the internal parameters, monitor the status of all input and output signals, and turn on input and output forcedly. I Idling A status in which the SI unit has received the FAIL SAFE command. The output can be cleared, held or forcedly switched on by setting parameters. ID No.

H The difference between the points when the Auto switch turns on and off, which is provided to prevent chattering. Hysteresis I Internal voltage drop The voltage applied between the COM and signal line when the Auto switch turns on. L Load current The current flowing to the load when the Auto switch turns on.

Bracket thickness is approx. 1.6mm Model Piping port size A B C D E F G H I J K L LFE13 3/8 90 73 40 23.5 56 83 89 24 6 1.6 96 87 LFE14 1/2 104 73 40 23.5 56 83 89 28 6 1.6 96 87 LFE26 3/4 105 78 50 29 67 94 100 35 6 1.6 115 106 LFE38 1 120 90 55 32 73 100 106 41 6 1.6 115 106 Model M N O P Q R S T U Bracket weight LFE13 48 39 4.6 12 11.5 52 28 2.5 depth 8.5 2 Approx. 45g LFE14 48 39 4.6

H Half-duplex Communication method that can send and receive data reciprocally in bi-directional communication. I Idle Base has received the FAIL SAFE command, and remains idle. The output state can be set to CLEAR, HOLD or Software Control using the parameter settings. IP address A 32 bit digit sequence which is assigned to identify devices which are connected to the network.

Function selection mode H Hysteresis Difference between the ON and OFF points of switch output. Hysteresis mode Refer to the "List of output modes" on page 39. I Insulation resistance Insulation resistance of the product. The resistance between the electrical circuit and the case.

Enclosed or poorly ventilated environment. h. Locations which are exposed to direct sunlight or heat radiation. i. Areas where strong electromagnetic noise is generated, such as strong electrical and magnetic fields or supply voltage spikes. j. Environment where static electricity is generated to the product. k. Locations where strong high frequency is generated. l.

[February 2017] H: Contents revised in several places. [July 2018] I: Contents are added. [May 2019] J: Contents revised in several places.

Enclosed or poorly ventilated areas. h. Locations which are exposed to direct sunlight or heat radiation. i. Areas where strong electromagnetic noise is generated, such as strong electrical and magnetic fields or supply voltage spikes. j. Areas where the product is exposed to static electricity discharge. k. Locations where strong high frequency is generated. l.

Areas that are dusty, or are exposed to splashes of water and oil drops. h. Areas exposed to direct sunlight (ultraviolet ray). i. Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease. Contact SMC for details. (2) Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.

(Full span, Full scale) H Hysteresis The difference between ON and OFF points used to prevent chattering. Hysteresis can be effective in avoiding the effects of pulsation. Mode where the switch output will turn ON when the flow is greater than the Set value, and will turn OFF when the flow falls below the Set value by the amount of hysteresis or more.

. -18No.PS-OMJ0004-E List of output mode If the point where the switch output is changed comes outside of set pressure range due to the change of set pressure, hysteresis(H) is automatically compensated. -19No.PS-OMJ0004-E Indication mode ( ) The display can be reversed. This setting is necessary to change the indication mode on receipt of the Pressure switch. 1.

Do not replace V111 (G, H, L, Without light SY100-82-1 M, W) to V115Y (DIN terminal), or vice versa. With light How to Use DIN Terminal Rated voltage Voltage symbol Part no. Connection 1. Loosen the holding screw and pull the connector out of the solenoid valve terminal block. DC24V 24VN SY100-82-3-05 DC12V 12VN SY100-82-3-06 AC100V 100VN SY100-82-2-01 AC200V 200VN SY100-82-2-02 2.

Specifications Fluid Air Note1) 1.5MPa(1.05MPa) Proof pressure Note1) 1.0MPa(0.7MPa) Max. operating pressure Note1) 0.05MPa(0.1MPa) Min. operating pressure Standard -5 to 60 deg.C (No freezing) Ambient and fluid temperature -H Note2) -5 to 80 deg.C (No freezing) -L Note3) -30 to 60 deg.C (No freezing) Note 1) ( ): Values for AS1000. Note 2) AS5000 is available as special.

Do not replace V114(G,H,L,M,W) to V115 (DIN terminal), and vice versa. type Coil Varistor type (Ground) W type WA type 10 No.SYJ3000-OMM0002-A SYJ Series/ / / /Specific Product Precautions 4 Be sure to read this before handling How to Use DIN Terminal Connector Assembly with Cover Connector assembly with dust proof protective cover Effective to prevention of short circuit failure due to the

Food Machinery Grease Specification Standard models -XC85 Grease pack part number: GR-H-010(10g) Nonfood compound incidental contact. Operating Environment Caution Environment for installing cylinder Do not use in food zone. * When the product is used in an area of liquid splash, or a water resistant function is required for the product, please consult SMC. 27 4-2.

Food Machinery Grease Specification Standard models -XC85 Grease pack part number: GR-H-010(10g) Nonfood compound incidental contact. Operating Environment Caution Environment for installing cylinder Do not use in food zone. 32 5.