Mechanically jointed rodless cylinder Basic type With Slide bearing guide type With cam follower guide type With linear guide type With High rigidity/ Linear guide type With Protective Cover type Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5m or smaller. 2. Install an aftercooler, air dryer or drain catch before the filter. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment. 3. Discharge condensates regularly.
: 201 to 300mm 80 40 50 50 20 20 Load weight m (kg) Load weight m (kg) Load weight m (kg) 20 10 10 10 63 63 63 5 5 5 50 50 50 [Example ] 40 40 40 1 1 1 70 100 300 500 1000 70 100 300 500 1000 70 100 300 500 1000 Stroke (mm) Stroke (mm) Stroke (mm) 2.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
20 12 10 20 20 20 40 LJ1H10 LJ1H20 LJ1H30 LJ1H10 LJ1H20 LJ1H30 LJ1H10 LJ1H20 LJ1H30 LJ1H10 LJ1H20 LJ1H30 2 Horizontal 8 25 25 18 Standard motor 8 12 8 12 24 5 10 5 10 Vertical 32 10 12 10 20 10 12 10 20 40 High rigidity direct acting guide LJ1H 20 20 40 44 Horizontal 50 25 25 60 Non-standard motor 8 12 8 12 66 5 10 5 10 Vertical 74 10 10 82 Options Page 100 Made to Order 101 Clean room
G46-10-01 2 pcs. G27-10-R1-X209 2 pcs. G27-10-R1-X209 2 pcs. G46-10-01 2 pcs.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
routed together with any high 3) Check whether the ionizer is used in an environment subject to OFF.)
Use the connector included as an accessory.
Flush button Pilot air exhaust port (Upper part of the side) Bleed valve open close 9.3 Mount the Heavy Duty Auto Drain IDFB60/70/80/90 Series 9-2 IDX-OM-V024 Chapter 10 Option R Chapter 10 Option R Option R is equipped with an earth leakage breaker (GFCI).
Operating Parameters Status Gas Operating pressure Proof pressure Burst pressure Ambient and operating temperature Cv Vacuum to 250 psig (1.7 MPa) Vacuum to 125 psig (0.9 MPa) 1000 psig (6.9 MPa) 8000 psig (55.2 MPa) 14 to 160F (10 to 71C) (No freezing) 1) 0.29 2 x 10-11 Pam3/sec 2 x 10-10 Pam3/sec 2) 4 x 10-9 Pam3/sec 2) Ra max 15 in. (0.4 m) Option: 10 in. (0.25 m), 7 in. (0.18 m), 5 in
Option Specification R 10 1 Safety instructions . 10 1 10 2 Specifications of GFCI . 10 1 10 3 How to connect the power supply . 10 2 10 4 Cautions for handling the GFCI . 10 2 10 5 Electrical Circuit . 10 2 Chapter 11 Specification for Option T 11 1 Safety instructions . 11 1 11 2 Specifications . 11 1 11 3 Remote operation . 11 1 11 4 How to connect the power supply and signal cable .
An alarm is generated if the PV value moves out of the alarm triggering range once and back into the range again. absolute value 4 Lower limit of the absolute value 8 Upper limit deviation 9 Lower limit deviation 10 Upper and lower limit deviation [Example] Set the alarm type to upper limit deviation hold. Display Operation procedure . 1. Make sure that the screen shows PV/SV display.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Supply 24 VDC 10% to the power supply for the input and control.
System Series MA3 10/15 Air Gripper: Rotary Actuated Type 10/15: MHR2-A310 10 15 10 MHR2-10-A310 10 MHR2-10-A310 15 MHR2-15-A310 With robot adapter PCD16 Finger closing port 61 With O-ring 18.5 Finger opening port 37 With O-ring 1 2 Use MA3 0-AM3 for the tool adapter.
(Refer to 2.3.1 Setting of contact input signal type and form) If an input from an external switch is detected, it can be generated as an alarm.Options to select continuous monitoring or monitoring during operation are available. Also, the detection start time after the start of operation and the detection end time can be set.
Air Supply Caution (1)Install an air filter. This may cause leakage or disconnection of the tubing. (10)Avoid installing and using fittings inside a food zone. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5m or finer. (2)Install an aftercooler, air dryer or water droplet separator, etc.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.
Series 10 12 16 20 25 32 40 50 63 80 100 MHZ2 3.0 5.0 7.0 7.0 8.0 8.5 MHZL2 6.0 7.0 10.0 11.0 MHL2 7.0 8.0 8.5 10.5 11.0 12.5 MHS2 6.5 7.0 7.5 8.5 MHS3, MHS(L)3 6.5 7.0 7.5 8.0 MHS4 6.5 7.0 7.5 8.5 MHC2 30 to -10 30 to 30 to 22.5 to -10 -10 -10 MHW2 88 to 54 to 58 to 41 to 30 to -4 -5 -6 -5 -5 Air cylinder Unit: mm Tube I.D.
Option R . 10-1 10.1 Safety instructions for use . 10-1 10.2 Specifications . 10-1 10.3 Connection of power supply . 10-2 10.4 Handling Precautions of the Earth Leakage Breaker . 10-2 10.5 Electrical circuit diagram . 10-2 Chapter 11 Inspection record .11-1 11.1 Inspection record . 11-1 IDF190D/240D Series IDX-OM-X011 Chapter 1 Safety Chapter 1 Safety 1.1 Before Using the Air Dryer Before