0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
Digital Pressure Sensor P.SET: Trimmer for pressure setting Vcc Brown ( ) D1 UNIT Black (O) D3 Tr Main computer Load LCD D2 Blue ( ) PLC Sequence Controller Wiring COM terminal MINUS in this case Environment Warning Brown ( ) D1 Vcc qThe sensor case is not water-proof; Do not immerse it in any liquid, or spil any liquid on the case. wGround the piping when induction noise is expected to be generated from piping.
Series ITV2090/2091 Dimensions ITV2090 Note) Do not attempt to rotate the cable connector, as it does not turn.
I EASY TO ATTACH SMALL DIAPHRAGM ACTUATORS The pneumatic and electrical ports are on the side of the body and do not interfere with the feedback lever on the other side. I STABLE OPERATION Control is very stable even on small sized actuators.
Panel mount Apply atmospheric pressure then do 0 clear. ZSP ISl ZSM 1 Turn screw 1/4 to 1/2 turn after panel makes contact with the sealing surface of the PSE. PFl IFl Removal from DIN rail Mounting on DIN rail 2a 2b Others Caution 1. Time delay for power on reset of controller is 0.5 seconds.
Do not pull on the cord.Have the case when remove the ECC-PNAL-232CAB cable. This cable might break when the code part of this cable is pulled when this cable is removed. Install the cover or the memory cassette after removing the ECC-PNAL-232CAB cable. Turn off the power supply when you install or detach the ECC-PNAL-232CAB cable.
Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
Do not set the mist generating pressure differential to exceed 0.2 MPa. Warning PPA 1. Before removing the oil filler plug, loosen it two and half turns to completely release the pressure in the bowl. This will prevent the oil filler plug from flying out.
When the line is stopped,do not adjust or set the differenital pressure, as it could cause the differential adjustment valve to break. 3. When setting the pressure differential, if there is a fluctuation in the operating flow rate, set the pressure differential at the lower flow rate range. ITV IC Inlet Outlet VBA VE VY1 G Piping PPA Warning Mist generation part AL 1.
Do not use a lubricator on the inlet side because it could clog the bleed holes and lead to a malfunction. 14-4-60 1 Regulator for 2 MPa Series ARX20 F.R.L.
Do NOT pipe upwards. AU200/300 Effective thread depth 6.5 4-M5 x 0.8 AU200, 300 Float type auto-drain Port size H G F E D C B A Model Port size 1 4 / 3 8 AU200 / 50 70 61 30 40.5 31.5 164 165 AU300 50 70 61 30 40.5 31.5 188.5 165 14-3-12
Do not use in an environment, where water or oil is splashed. Because it is the open type construction. If water or oil were to make an ingress, the electrical circuit would be corroded and result in a malfunction or damage. 2. Operating fluids are either air or inert gas exclusively. Never use liquids. 3. Never use in an environment where flammable fluid or gas is used.
Therefore, do not operate it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). 2.
Do not use in locations where there is splashing or spraying of oils and solvents. 3. When using a commercially available switching regulator, be sure to ground the FG terminal. OUT2 OUT1 SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1) Set point ON When assembling the connector to the switch housing, push the connector straight onto the pins until the lever locks into the housing slot.
The silencer's response properties do not change in the initial stage, but will change due to the blockage after long use. Replace it after using about 500,000 times. This number is subject to change based on fluid quality and energization time. 2. When using a silencer, make space for silencer replacement. 1.The controller starts its output the moment the power switch is turned ON.
BRAZIL SMC Pneumaticos Do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. VENEZUELA SMC Neumatica Venezuela S.A. ASIA CHINA SMC (China) Co., Ltd. HONG KONG SMC Pneumatics (Hong Kong) Ltd. INDIA SMC Pneumatics (India) Pvt. Ltd. MALAYSIA SMC Malaysia (S.E.A.) Sdn. Bhd. PHILIPPINES SMC Pneumatics (Philippines), Inc. SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.