Air Suction Filter Series ZFA 1 Do not use it in a line that is kept pressurized because it could cause the body to break. 13-10-2 3 Air Suction Filter Series ZFA 100 200 Dimensions: ZFA Single unit Bracket ZX ZR Cover opened-up dimensions 70 Element extracted dimensions 55 ZM ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800)
Do not use it in a line that is kept pressurized because it could cause the body to break. 13-10-5 3 Series ZFB Dimensions Element Replacement 1. Stop the operation and reduce the internal pressure of the filter to atmospheric pressure. 2.
Do not apply an impact or large forces to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirt's deformation range. Positioning should be performed accurately.
Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range. Positioning should be performed accurately. Especially in the case of small diameter pads. 6.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.
(Do not cut the tube with plier6, nippers, scissors, utilitv knife, etc.) ePull out the tube while keeping the release button depressed. lJf the release butlon is nol held down, the tube cannot be withdrawn.) OGrasp the tube, then slowly push it until il comes lo a dead-end.
Do not attempt to disassemble tublng lrom fitting with vehicle air system under pressure, Glnflhd hhftilco ffiilt hr:iffi,bJn-|d$u[,ru,fl OHighly sistrrt OGradually corro&s (clpends on oporating conditions) Vl,lodelEl8ly .onodes (depends on opelating conditions) Not r6commnd6d br high concnlcrlions & )posur l coraoded Body Stud Guide Body Chuck Releass Bushing Collet Oring Packing SMC For
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
swirches Pfessrre to the side irdicated by label B rotales the shaft clockwise, pressu to the side hbeled A rciates the shaft countercl@kwise, l{cnAtB\lv3o l,rcRAroso--10() o Series:NCRAl Shaft Load fr"u lvlc&l direclion Fsa Fsb $cRAAUrgt 6 cnAtaso 110 44 44 NcRAlffl 132 44 ffi NCf,Ant8() 198 44 NCnA1otOO 220 44 In the stop position, the load can meet the value given in lhe list, please do
Not 3) Aor3 6 15 (basic typ) ar tully pod6d and do not rqunettl x150 optton. Specifications
Lubrication aTh yah,e h8 bon lub,ric.td ior ltb d nrlnubcfrirE. and dor noa lqoirr fudfiar fubdcdion in svba. ef a lubricant is used in the system, use turbine oil type #1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate, as the original lubricant applied during manuiacturing will have been washed away. See table of suggested lubricants.
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?