MHC2 1 Piston B Ass,y C shape snap ring Carbon steel Nickel plated e !2 High carbon chrome bearing steel Cylindrical roller Finger Heat treated Electroless nickel plated Carbon steel r !3 Brass Needle Ass'y Side roller Nitriding Electroless nickel plated Carbon steel t !4 Brass Exhaust plug Level shaft Nitriding Electroless nickel plated Stainless steel y !
5 y !9 e !7 MHF2-8D2 i !6 Parts list Parts list Note No. Description No.
9 t y !5 i u !6 q r !0 !1 !2 Fingers closed Normally closed !4 !3 Component Parts Component Parts Note Material Material Note No. q w e t y u No. i o !0 !1 !2 !3 !4 !
plate Slider cover assembly Diaphragm plate assembly Diaphragm ring Aluminum alloy Aluminum alloy Special brake lining Stainless steel Stainless steel Stainless steel Carbon steel Carbon steel Hard anodized Hard anodized Cam follower cap Tube cover Brake shoe Joint ring Air coupler 2 Brake disc Manual rod 1 Manual rod 2 Brake spring Air tube Cable Tube guide assembly Guide rod q w e r t y
Pitch moment Yaw moment MXY12 MXY12 MXY12 0.035 0.030 0.025 0.020 0.015 0.010 0.005 0 0.030 0.025 0.020 0.015 0.010 0.005 0 0.05 MXY8 Table deflection mm Table deflection mm Table deflection mm MXY8 MXY8 MXY6 0.04 MXY6 MXY6 0.03 0.02 0.01 0 Load N 0 20 40 60 80 100 Load N 0 20 40 60 80 100 Load N 0 50 100 150 200 250 8-9-10 10 Air Slide Table Long Stroke Type Series MXY Construction @3 y
3 Stopper Stainless steel NBR Gasket Special packing y !4 Bearing High carbonate chrome steel O ring NBR u !5 Back-up ring O ring NBR Stainless steel i !
Aluminum alloy 19 42 CYP32 only Nickel plated Hexagon socket head cap screw Bumper Urethane Chrome molybdenum steel 20 43 Clear hard anodized Plate A O-ring NBR Aluminum alloy 21 44 Clear hard anodized Plate B C type snap ring for shaft Carbon tool steel Aluminum alloy 22 45 Cushion seal O-ring NBR NBR 3 Clean Room Rodless Cylinder Series CYP Dimensions E Depth ED 4-MM Thread depth M L T Y
42 CYP32 only Nickel plated Urethane Hexagon socket head cap screw Bumper Chrome molybdenum steel 20 43 Clear hard anodized NBR Plate A O-ring Aluminum alloy 21 44 Clear hard anodized Carbon tool steel Plate B C type snap ring for shaft Aluminum alloy 22 45 NBR Cushion seal O-ring NBR 6 Clean Room Rodless Cylinder Series CYP Dimensions (mm) 1in = 25.4mm E Depth ED 4-MM Thread depth M T Y
42 CYP32 only Nickel plated Urethane Hexagon socket head cap screw Bumper Chrome molybdenum steel 20 43 Clear hard anodized NBR Plate A O-ring Aluminum alloy 21 44 Clear hard anodized Carbon tool steel Plate B C type snap ring for shaft Aluminum alloy 22 45 NBR Cushion seal O-ring NBR 6 Clean Room Rodless Cylinder Series CYP Dimensions (mm) 1in = 25.4mm E Depth ED 4-MM Thread depth M T Y
Material Replacement Parts Material Note Component Parts VQZ No. q w e r t y No. !0 !
(Loosen in the case of Y-shape type terminal.) As shown in the below figure, mount a crimped terminal (9), and then again tighten the screw (3e). Note) Tighten within the tightening torque of 0.5 Nm15%. Note: a It is possible to wire even in the state of bare wire.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com C: Locking type (Manual) 2 position double (rubber) 4 position dual 3 port valve (C) (A) 4 (B) 2 Standard type (1 W) High pressure type (1.0 MPa) Negative COM External pilot Low wattage type (0.5 W) Nil K N R Y (A) 4 (B) 2 Note 1) C Note) 5 (R1) 3 (R2
Description AXT336-1A-1 01 02 01 02 01 02 02 03 02 03 02 03 02 03 Manifold block assembly AXT336-1A-2 AXT336-1A-3 AXT336-2A-1AXT336-2A-2AXT336-3A-1AXT336-3A-2q End plate (U side) assembly w End plate (D side) assembly e Terminal assembly Junction cover assembly Tie-rod r t y Replacement Parts No. u Description Material Carbon steel NBR NBR Part no.
s2 in X, Y, Z directions, 3 times each (De-energized)?
s2 in X, Y, Z directions, 3 times each (De-energized)?
s2 in X, Y, Z directions, 3 times each (De-energized)?
s2 in X, Y, Z directions, 3 times each (De-energized)?
15 to +10% of rated voltageEquivalent to B type (130C)5.6 VA (50 Hz), 5.0 VA (60 Hz)3.4 VA (2.1 W)/50 Hz, 2.3 VA (1.5 W)/60 Hz1.8 WGrommet, Type D DIN terminal, Type Y DIN terminalIndicator light/Surge voltage suppressor (2)Non-locking push type (Flush),Locking type (Tool required), Locking type (Lever)
s2 in X, Y, Z directions, 3 times each (De-energized)?
10 to 60C (No freezing or condensation)Operating/Stored: 35 to 85% RH (No condensation)250 VAC for 1 minute between live parts and case2 M or more between live parts and case (at 50 VDC Mega)10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized)100 m/s2 in X, Y, Z directions, 3 times each (De-energized)?