Model Type: Standard, Piping: Immersion Type, Tank Size: 6 Inch, IN/OUT Port Size: 10 [1 (25A)], Thread: Rc, Outlet Pipe Dimensions: Pipe Projection: Long; Thread Type: G, Rated Voltage: None, Electrical Entry: None, Fluid and Ambient Temperature: -40 to 60°C, Silencer: without Silencer, Pilot Port Size: 1/8, Orifice Diameter: -
Model Type: Standard, Piping: Immersion Type, Tank Size: 5 inch, IN/OUT Port Size: 10 [1 (25A)], Thread: NPT, Outlet Pipe Dimensions: Pipe Projection: Short; Thread Type: None, Rated Voltage: None, Electrical Entry: None, Fluid and Ambient Temperature: -40 to 60°C, Silencer: without Silencer, Pilot Port Size: 1/8, Orifice Diameter: -
Series: 25A-PFMB7, Rated Flow Range: 201(2 to 200 L/min), Port Size: C8 [ø8 (5/16") One-touch Fitting], Piping Entry Direction: Straight, Output Specification: Out 1: NPN, Out 2: Analog 4 to 20mA, Lead Wire: Lead Wire w/Connector 2 m, Rubber Cover for Connector, Silicone Rubber, Unit Specifications: -
Series: 25A-PFMB7, Rated Flow Range: 201(2 to 200 L/min), Port Size: C8 [ø8 (5/16") One-touch Fitting], Piping Entry Direction: Straight, Output Specification: Out 1: NPN, Out 2: NPN, Lead Wire: Lead Wire w/Connector 2 m, Rubber Cover for Connector, Silicone Rubber, Unit Specifications: SI Unit Only
Series: 25A-ISE20, Rated Pressure Range: C (-0.1 to 1 MPa), Output Specification: Y (PNP Open Collector 2 Outputs + Copy Function), Unit Specifications: P (Unit Selection Function, Initial value psi), Piping Specification: 02 [R1/4, (M5, Female Threaded)], Lead Wire: W (Lead Wire w/Connector, 5-core, 2 m Lead Wire, Waterproof)
.: 25 (Port Size: 25A, Pipe O.D.: 32mm), Output Specification: E (OUT1: PNP; OUT2: Analog 1 to 5V), Lead Wire: Lead Wire w/M8 Connector, 3m, Unit Specification: M (Instantaneous Flow Rate: L/min; Accumulated Flow: L; Temp: °C)
Series: 25A-LEFS (Secondary Battery, Ball Screw Drive), Accuracy: Basic Type, Size: 40, Motor Mounting Position: R (Right Side Parallel), Motor Type: Step Motor (Servo/24 VDC), Lead Screw: A (LEFS16: 10mm, LEFS25: 12mm, LEFS32: 16mm, LEFS40: 20mm), Stroke: 600mm, Motor Option: w/o Option, Positioning Pin Hole: Housing B Bottom, Actuator Cable Type: S (Standard Cable), Actuator Cable Length
IP65 enclosure; Thread piping, one-touch fitting, or flange piping; Standard NBR seal and Class B coil insulation; Other options: low concentration ozone resistant and applicable to deionized water, oil-free, port threads; Series 25A-VXD is compatible with secondary battery applications
IP65 enclosure; Thread piping, one-touch fitting, or flange piping; Standard NBR seal and Class B coil insulation; Other options: low concentration ozone resistant and applicable to deionized water, oil-free, port threads; Series 25A-VXD is compatible with secondary battery applications
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. Non-rotating rod: double acting single rod, Bore sizes: 20, 25, 32, and 40 *, Strokes from 25mm through 300mm, Mounts: basic,
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. Double acting single rod, Bore sizes: 20, 25, 32, and 40 *, Strokes from 25mm through 500mm, Mounts: basic, foot, front and rear
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. Double acting single rod, Bore sizes: 20, 25, 32, and 40 *, Strokes from 25mm through 500mm, Mounts: basic, foot, front and rear
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP. The series is designed for high side load applications found in material handling, lifting and stopping. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. Double acting single rod, Bore sizes: 20, 25, 32, and 40 *, Strokes from 25mm through 500mm, Mounts: basic, foot, front and rear